
P311-5C8524C 19-2984 New
4773004090 , 4773004092 , 4773035411
- Remanufactured Unloaded Caliper
- Casting # 13WG Installation Hardware Included with Metal Piston
- Remanufactured Brake Caliper
- Product Attributes:
-
- Abutment Clips Included: No
- Anti-Rattle Spring Included: Yes
- Bleeder Screw Cap Included: No
- Bleeder Screw Included: Yes
- Bleeder Screw Quantity: 1
- Bleeder Thread Size: M7x1.0
- Bracket Included: No
- Caliper Color: Gray
- Caliper Finish: Oil Emulsion
- Caliper Slides Included: Yes
- Caliper Type: Floating
- Casting Number: 13wg
- Contains Electronic Components: No
- Disc Brake Caliper Casting Material: Cast Iron
- Does it require SDS: No
- Dust Boots Included: Yes
- E-Waste: No
- FAA_A1: Not Recommended. The O.e. Manufacturers Specified Steel Or Phenolic Pistons Based On The Intended Use Of The Vehicle. It Is Recommended That The Installer Follow The Manufacturer’s Recommendations.
- FAA_A2: As A Rule, Always Use Brake Fluid Recommended By O.e. The Fluid Type Is Stamped On The Master Cylinder Reservoir Lid. Always Use New Fluid In A Sealed Container.
- FAA_A3: Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Also Ensure That Brake Hoses Are Not Collapsed Or Restricted And Inspect Steering/suspension Components For Proper Operation.
- FAA_A4: Brake Squeal Can Be Caused By Improper Installation Of The Brake Pads, Improperly Installed Brake Hardware And Improper Brake Rotor Finish.
- FAA_A5: A Symptom Of A Low Brake Pedal Is Usually Caused By Air In The System, Misadjusted Rear Brake Shoes, Deteriorated Brake Hose(s) Or A Defective Master Cylinder.
- FAA_A6: A Silicone Grease Is Used On Floating Caliper Mounting Pins.
- FAA_A7: New Hardware Is Included With All Of Our Calipers However The Mounting Bracket Is An Added Option Depending On Part Number And Application. Mounting Brackets Are Also Sold Separately For Most Applications.
- FAQ_Q1: Can I Switch Out A Phenolic Piston Caliper For A Steel Piston Caliper Or Vice Versa?
- FAQ_Q2: What Type Of Fluid Should I Use: Dot 3, Dot 4, Or Dot 5?
- FAQ_Q3: Car Pulls To One Side During Braking. Why?
- FAQ_Q4: Brakes Squeal All Of The Time. What's Causing The Squeal?
- FAQ_Q5: Could Calipers Be The Cause Of A Low Brake Pedal?
- FAQ_Q6: What Type Of Grease Is Used On Floating Caliper Mounting Pins?
- FAQ_Q7: Do All Of Your Calipers Come With The New Hardware And A Mounting Bracket For Installation?
- Grade Type: Regular
- Inlet Fitting Type: Flare
- Inlet Port Size:
- 0.394
- 10.00366
- Inlet Thread Size: M10x1.0
- Is Item A Chemical: No
- Is Or Contains A Battery: No
- Is Or Contains A Bulb: No
- Is Prop Sixty Five Affected: No
- Is the item CARB affected: No
- Mounting Bolt Included: No
- Mounting Bracket Included: No
- Mounting Hardware Included: Yes
- Mounting Hole Diameter:
- 0.465
- 11.80635
- Mounting Hole Thread Diameter:
- 0.465
- 11.80635
- Pad Wear Sensor Included: No
- Pads Included: No
- Piston Diameter:
- 1.784
- 45.3136
- Piston Material: Steel
- Piston Quantity: 4
- Product Condition: Remanufactured
- Rust Resistant Coating: Yes
-
Features:
- Pistons are durable, resistant to cracking or pitting and handle great loads.
- Rubber seals are replaced with new high temperature EPDM rubber for extended life and optimum performance.
- Mounting bracket is included where applicable for a hassle-free installation.
- Calipers are treated with a special formulated rust inhibitor and kept in the original equipment finish.
- New banjo bolts are included where applicable to ensure a perfect fit and quick installation.
- New bleeder screws provide trouble-free bleeding and a positive seal.
- New washers are included where applicable for a proper seal.
- A plastic cap plug protects every brake port thread to ensure trouble-free installation.
- New stainless steel hardware clips and new mounting pins are included where applicable.
- As a remanufactured Original Equipment part, this unit guarantees a perfect vehicle fit.
- Our remanufacturing process is earth-friendly, as it reduces the energy and raw material needed to make a new part by 80%.
- Expertly remanufactured to rigorous quality and performance standards, all CARDONE Brake Calipers are equipped with brand-new, premium components to guarantee exceptional longevity and reliability. These remanufactured brake calipers are 100% pressure-tested to deliver consistent, industry-leading brake performance. Each unit arrives with a complete set of brand-new hardware for a simple, complete installation. Caliper bracket is included when applicable.