Shop Chevrolet Tracker Mirrors

2004
GMC Yukon SLT
5.3L V8 flexfuel

The mirror on my yukon was shattered. I just got a new one (glass only) and need to install it into the existing housing. How do i remove the cap, without damaging anythig? Then is there any special way to put the new mirror on? or does it just clip? This is a motorized unit with turn signal. Thanks for any help.

1. Adjust the mirror face as shown in the picture to obtain access to the mirror face retention clips.
2. Position a flat-bladed tool between the back side of the mirror face and the adjuster mechanism as shown in the picture
3. Place the blade of the tool between the gasket (1) and the adjuster mechanism (2).
4. Slightly twist the blade of the tool while gently pulling the mirror face towards you in order to release the retainers (3).
5. With the mirror face in hand, disconnect the electrical connectors.
6. Remove the mirror face from the mirror housing.
7. Inspect the adjuster mechanism for damage.

1. Inspect the components for any damage. Ensure that the mirror face has all the retention clips in place.
2. Plug in the electrical connectors to the back of the mirror.
3. Align the mirror face retention clips with the adjuster mechanism
4. Gently press the mirror back into the adjuster mechanism with the palm of the hand on the center of the glass until it locks into place.
5. Inspect the operation of the mirror.

Can anyone recommend an adhesive to stick my wing mirror in place? I bought sticky pads from Halfords but they were useless and the mirror vibrates as I'm going along. I've got it held in place with back tape on either side. Should I have stuck the new mirror on top of the old one? My car is an old Toyota Previa people carrier, P reg.

are you replacing the entire mirror glass? or getting one of those convex spot mirrors??? for the spot mirrors 3M makes a body molding double sided tape that is dam near impossible to remove once installed to a clean surface.

if your doing the entire mirror because the old glass broke, you might have to get the complete assembly.

ford focus
2003
5 speed manual
48,000 miles

i knocked the driver-side mirror off. the electronics still work and the mirror is not broken either. is this an easy repair and can i purchase just the mount?

any help would be grand,

thanks

You need to buy the entire mirror. You need to remove the door panel and you will see some holes in the door. Inside these holes will be the screws that hold the mirror assembly on. Disconnect wiring and unbolt mirror. Replace with new.

How does one replace the reflective mirror surface on a 2003 Dodge caravan side view mirror (driver side), I have the part but I am puzzled as how to remove and replace the mirror surface.

An auto glass adhesive is usually used to glue the glass to the plastic. I have seen the rear view mirror adhesive work on these.

Steve

So Steve 01832,
should I just brake off the remaining reflective surface and glue the new mirror into place.

Be very careful you don't crack the plastic piece. You may want to wear gloves also. I usually don't advise replacing the mirrored glass. I usually replace the entire mirror. I've found that the aftermarket adhesives tend not to hold the glass longterm.

Steve

Steve, thanks for the tips.

Hello

I have Toyota Corolla 2002, and I recently lost my left side mirror and here is how it looks like it.

I initially called several places to get it fixed, but it seems way too much so I am thinking about fix it by myself. It looks like my mirror is the only thing gone (panel and everything is there).
I was curious if I can just buy a left mirror part (such as link deleted), and do the similar fix as link deleted? Would it be okay or is it too dangerous to attach the mirror like that (like attaching the mirror by adhesive pad...would it be strong enough to do so)?
Do I need to completely change the left mirror (including the shell like link deleted
Could you please help me/advice me on what to do?
Thank you very much

Sincerely,



Links were deleted ......................... not allowed

I mean I am curious if I need to replace the complete left mirror (including shell) or if I can just put a mirror only (mirror itself with adhesive pad or so in that panel)?
I am only missing a mirror in there but I am quiet sure by putting a glue/adhesive pad is strong or safety enough to do so.
Thanks