Finish Selecting Your Vehicle to Shop For Your Wheel Speed Sensor

Choose a Year for your Chevrolet 's Wheel Speed Sensor

  • 2021
  • 2020
  • 2019
  • 2018
  • 2017
  • 2016
  • 2015
  • 2014
  • 2013
  • 2012
  • 2011
  • 2010
  • 2009
  • 2008
  • 2007
  • 2006
  • 2005
  • 2004
  • 2003
  • 2002
  • 2001
  • 2000
  • 1999
  • 1998
  • 1997
  • 1996
  • 1995
  • 1994
  • 1993
  • 1992
  • 1991
  • 1990
  • 1989
  • 1988
Show More Years

Shop By Brand

The Following brands are available based on your search.

  • ACDelco
    ACDelco
  • Bosch
    Bosch
  • Delphi
    Delphi
  • Dorman
    Dorman
  • Holstein
    Holstein
  • Pex
    Pex
  • SKF
    SKF
  • Standard Ignition
    Standard Ignition
  • True Tech
    True Tech
  • Vemo
    Vemo
  • WSO
    WSO

Best Selling Genuine Chevrolet Wheel Speed Sensors

  • We Stock the following top leading brands, including ACDelco
  • Constantly Updated Inventory of Chevrolet Replacement Wheel Speed Sensor Parts

ACDelco
2004 Chevrolet Silverado 1500 ABS Wheel Speed Sensor ACDelco

P311-0573CC6    W0133-2552756  New

Qty:
In Stock & Ready to Ship
$41.42
ACDelco ABS Wheel Speed Sensor
  • This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
  • Genuine GM
Brand: ACDelco
Additional Fitment Information:
Vehicle Submodel
2004 - Chevrolet Silverado 1500 Z71
ACDelco
2004 Chevrolet Silverado 1500 ABS Wheel Speed Sensor ACDelco

P311-0573CC6    W0133-2552756  New

Qty:
In Stock & Ready to Ship
$41.42
ACDelco ABS Wheel Speed Sensor
  • This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
  • Genuine GM
  • with Spring Package (RPO B2E)
Brand: ACDelco
Additional Fitment Information:
Vehicle Drive Type
2004 - Chevrolet Silverado 1500 RWD
ACDelco
2006 Chevrolet Silverado 1500 ABS Wheel Speed Sensor ACDelco

P311-0573CC6    W0133-2552756  New

Qty:
In Stock & Ready to Ship
$41.42
ACDelco ABS Wheel Speed Sensor
  • This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
  • Genuine GM
  • with 7,200 lbs Vacuum Power Brakes (RPO JC4) or 6,400 lbs Hydraulic Power Brakes (RPO JH1) or 7,200 lbs Hydraulic Power Brakes (RPO JH2)
Brand: ACDelco
Additional Fitment Information:
Vehicle Drive Type
2006 - Chevrolet Silverado 1500 4WD
ACDelco
2003 Chevrolet Silverado 1500 HD ABS Wheel Speed Sensor ACDelco

P311-0573CC6    W0133-2552756  New

Qty:
In Stock & Ready to Ship
$41.42
ACDelco ABS Wheel Speed Sensor
  • This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
  • Genuine GM
  • with 7,200 lbs Vacuum Power Brakes (RPO JC5) or 7,200 lbs Hydraulic Power Brakes (RPO JH5)
Brand: ACDelco
Additional Fitment Information:
Vehicle Drive Type
2003 - Chevrolet Silverado 1500 HD 4WD
ACDelco
2012 Chevrolet Avalanche ABS Wheel Speed Sensor ACDelco

P311-01347D9    W0133-1990801  New

Qty:
In Stock & Ready to Ship
$104.08
ACDelco ABS Wheel Speed Sensor
  • This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
  • Genuine GM
  • Incl.ABS Wheel Speed Sensor Wire Harness
Brand: ACDelco
Additional Fitment Information:
Vehicle
2012 - Chevrolet Avalanche
ACDelco
2000 Chevrolet Silverado 1500 ABS Wheel Speed Sensor ACDelco

P311-1C442E6    W0133-2552754  New

Qty:
In Stock & Ready to Ship
$39.29
ACDelco ABS Wheel Speed Sensor
  • This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
  • Genuine GM
Brand: ACDelco
Additional Fitment Information:
Vehicle Drive Type
2000 - Chevrolet Silverado 1500 RWD
ACDelco
2007 Chevrolet Suburban 1500 ABS Wheel Speed Sensor ACDelco

P311-4108EA0    W0133-2552757  New

Qty:
In Stock & Ready to Ship
$41.42
ACDelco ABS Wheel Speed Sensor
  • This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
  • Genuine GM
Brand: ACDelco
Additional Fitment Information:
Vehicle
2007 - Chevrolet Suburban 1500
ACDelco
2002 Chevrolet Silverado 2500 HD ABS Wheel Speed Sensor ACDelco

P311-0DAD8EB    W0133-2034982  New

Qty:
In Stock & Ready to Ship
$68.80
ACDelco ABS Wheel Speed Sensor
  • This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
  • Genuine GM
Brand: ACDelco
Additional Fitment Information:
Vehicle
2002 - Chevrolet Silverado 2500 HD
ACDelco
2004 Chevrolet Suburban 1500 ABS Wheel Speed Sensor ACDelco

P311-0EABA62    W0133-1852789  New

Qty:
In Stock & Ready to Ship
$179.25
ACDelco ABS Wheel Speed Sensor
  • This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
  • Genuine GM
Brand: ACDelco
Additional Fitment Information:
Vehicle
2004 - Chevrolet Suburban 1500
ACDelco
2004 Chevrolet Express 2500 ABS Wheel Speed Sensor ACDelco

P311-0EABA62    W0133-1852789  New

Qty:
In Stock & Ready to Ship
$179.25
ACDelco ABS Wheel Speed Sensor
  • This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
  • Genuine GM
  • Excluding 7,300 Lbs. GVW
Brand: ACDelco
Additional Fitment Information:
Vehicle
2004 - Chevrolet Express 2500
ACDelco
2015 Chevrolet Cruze ABS Wheel Speed Sensor ACDelco

P311-0AAEF64    W0133-2195116  New

Qty:
In Stock & Ready to Ship
$32.00
ACDelco ABS Wheel Speed Sensor
  • This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
  • Genuine GM
  • Incl.ABS Wheel Speed Sensor Wire Harness
Brand: ACDelco
Additional Fitment Information:
Vehicle
2015 - Chevrolet Cruze
ACDelco
2006 Chevrolet Silverado 1500 ABS Wheel Speed Sensor ACDelco

P311-1C442E6    W0133-2552754  New

Qty:
In Stock & Ready to Ship
$39.29
ACDelco ABS Wheel Speed Sensor
  • This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
  • Genuine GM
  • with 7,200 lbs Vacuum Power Brakes (RPO JC4) or 6,400 lbs Hydraulic Power Brakes (RPO JH1)
Brand: ACDelco
Additional Fitment Information:
Vehicle Submodel Drive Type
2006 - Chevrolet Silverado 1500 LS RWD
ACDelco
2004 Chevrolet Silverado 1500 ABS Wheel Speed Sensor ACDelco

P311-1C442E6    W0133-2552754  New

Qty:
In Stock & Ready to Ship
$39.29
ACDelco ABS Wheel Speed Sensor
  • This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
  • Genuine GM
  • w/o Spring Package
Brand: ACDelco
Additional Fitment Information:
Vehicle Drive Type
2004 - Chevrolet Silverado 1500 RWD
ACDelco
1996 Chevrolet Tahoe ABS Wheel Speed Sensor ACDelco

P311-1D9ECF1    W0133-1684769  New

Qty:
In Stock & Ready to Ship
$40.50
ACDelco ABS Wheel Speed Sensor
  • This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
  • Genuine GM
  • Bolt on with Bracket
Brand: ACDelco
Additional Fitment Information:
Vehicle Transmission Drive Type
1996 - Chevrolet Tahoe Automatic RWD
ACDelco
2014 Chevrolet Traverse ABS Wheel Speed Sensor ACDelco

P311-3B41133    W0133-2044806  New

Qty:
In Stock & Ready to Ship
$62.93
ACDelco ABS Wheel Speed Sensor
  • This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
  • Genuine GM
  • Incl.ABS Wheel Speed Sensor Wire Harness
Brand: ACDelco
Additional Fitment Information:
Vehicle
2014 - Chevrolet Traverse
ACDelco
2006 Chevrolet Silverado 1500 ABS Wheel Speed Sensor ACDelco

P311-0DAD8EB    W0133-2034982  New

Qty:
In Stock & Ready to Ship
$68.80
ACDelco ABS Wheel Speed Sensor
  • This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
  • Genuine GM
  • with 9,900 lbs Hydraulic Power Brakes (RPO JH6)
Brand: ACDelco
Additional Fitment Information:
Vehicle
2006 - Chevrolet Silverado 1500
ACDelco
2001 Chevrolet Silverado 1500 HD ABS Wheel Speed Sensor ACDelco

P311-1A780BF    W0133-2003451  New

Qty:
In Stock & Ready to Ship
$77.40
ACDelco ABS Wheel Speed Sensor
  • This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
  • Genuine GM
  • Location-Transfer Case
Brand: ACDelco
Additional Fitment Information:
Vehicle
2001 - Chevrolet Silverado 1500 HD
ACDelco
2014 Chevrolet Traverse ABS Wheel Speed Sensor ACDelco

P311-524CEEA    W0133-1990790  New

Qty:
In Stock & Ready to Ship
$56.64
ACDelco ABS Wheel Speed Sensor
  • This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
  • Genuine GM
  • Incl.ABS Wheel Speed Sensor Wire Harness
Brand: ACDelco
Additional Fitment Information:
Vehicle
2014 - Chevrolet Traverse
ACDelco
2013 Chevrolet Silverado 1500 ABS Wheel Speed Sensor ACDelco

P311-5244BF2    W0133-1990821  New

Qty:
In Stock & Ready to Ship
$86.62
ACDelco ABS Wheel Speed Sensor
  • This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
  • Genuine GM
  • Includes ABS Wheel Speed Sensor Wire Harness
Brand: ACDelco
Additional Fitment Information:
Vehicle
2013 - Chevrolet Silverado 1500
ACDelco
2014 Chevrolet Malibu ABS Wheel Speed Sensor ACDelco

P311-03AF5AC    W0133-2214184  New

Qty:
In Stock & Ready to Ship
$32.72
ACDelco ABS Wheel Speed Sensor
  • This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
  • Genuine GM
  • Incl.ABS Wheel Speed Sensor Wire Harness
Brand: ACDelco
Additional Fitment Information:
Vehicle
2014 - Chevrolet Malibu

Latest Car Advice

CarJunky AutoAdvice

brake system

Showing 2 out of 4 Posts | Show 2 Hidden Posts
Question From edson on brake system

2005 chevy silverado 1500 4.3liter engine 147,000 miles brake pedal vibrates and pedal goes lower right before astop and there is also a noise under the hood when this happens

Response From Discretesignals Top Rated Answer

How slow? Like parking lot maneuvers or below 5 mph?

ECHNICAL

Bulletin No.: 03-05-25-007D

Date: May 01, 2009

Subject: Antilock Brake (ABS) Activation At Low Speeds (Clean Wheel Speed Sensor Mounting Surface)

Models:
2002-2006 Cadillac Escalade, Escalade EXT
2003-2006 Cadillac Escalade ESV
1999-2006 Chevrolet Silverado
2001-2006 Chevrolet Suburban, Tahoe
2002-2006 Chevrolet Avalanche
2003-2006 Chevrolet Express
2007 Chevrolet Silverado Classic
1999-2006 GMC Sierra
2001-2006 GMC Yukon, Yukon Denali, Yukon XL, Yukon Denali XL
2003-2006 GMC Savana
2007 GMC Sierra Classic
2003-2006 HUMMER H2
................................................................................
Supercede:
This bulletin is being revised to add the 2007 Silverado/Sierra Classic models. Please discard Corporate Bulletin Number 03-05-25-007C (Section 05 - Brakes).
................................................................................
Condition

Some customers may comment on ABS activation at low speeds, usually below 8 km/h (5 mph). Upon investigation, the technician will find no DTCs set.

Cause

The cause of this condition may be an increased air gap between the wheel speed sensor and the hub reluctor ring due to rust and debris built up on the sensor mounting surface.

Correction

Measure AC voltage and clean the wheel speed sensor mounting surfaces.

1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in the General Information sub-section of the Service Manual.
2. Disconnect both the front wheel speed sensor connectors at the frame and harness.
3. Place a Digital Volt Meter (DVM) across the terminals of each wheel speed sensor connector.
4. Rotate the wheel clockwise approximately one revolution per second. The minimum reading should be at least 350 ACmV's. If the reading is less than 350 ACmV's, remove the wheel speed sensor. Refer to the applicable Wheel Speed Sensor Replacement procedure in the ABS sub-section of the Service Manual.
5. Plug the wheel speed sensor bore in order to prevent debris from falling into the hub during service.
6. Clean the wheel speed sensor mounting surface using a wire brush, sand paper, emery cloth, scotch brite, or other suitable material. Be sure to thoroughly clean the wheel speed sensor surface. There should be no rust or corrosion.
7. Check the sensor head to determine if it has been warped/distorted due to the corrosion build up or other causes. Check the mounting surface on the sensor head for flatness by placing it on the edge of a metal machinists scale or other suitable straight edge to measure the flatness. Check the sensor for flatness in multiple (minimum 3) positions/directions. If the sensor head is distorted, replace the sensor.
8. Apply (spray) two thin coats of the specified rust penetrating lubricant (corrosion inhibitor) to the complete sensor mounting surface on the bearing hub. Allow to dry for 3-5 minutes between coats. Use ONLY Rust Penetrating Lubricant, P/N 89022217 (in Canada, P/N 89022218).
9. When the corrosion inhibitor is dry to the touch (about 10 minutes), apply a thin layer of bearing grease to the hub surface and sensor O-ring prior to sensor installation. Use ONLY Wheel Bearing Lubricant, P/N 01051344 (in Canada, P/N 993037).
10. Install either the original sensor or a new one in the hub. Ensure that the sensor is seated flush against the hub. Refer to the applicable Wheel Speed Sensor Replacement procedure in the ABS sub-section of the Service Manual.
11. Place the DVM across the sensor terminals and recheck the voltage while rotating the wheel. The voltage should now read at least 350 ACmV's.

Response From edson

thank you for your advice i will get back to you if this helps

Response From edson

below 5 mph

2002 Alero humming noise - ABS, Trac Off lights on

Showing 2 out of 13 Posts | Show 11 Hidden Posts
Question From ez50nj on 2002 Alero humming noise - ABS, Trac Off lights on

I've had a humming/tire separation type noise for about 6 months when I decelerate to 30 mph. About 2 months ago the Trac Off, ABS, and Service Engine Soon lights came on. Private repair shop ran scanner which indicated excessive wheel spin. One code left front, 2 codes right front. Tech advised wheel bearings worn so I replaced both. Driving out of shop all three lights back on.

The car feels tighter, but I still get the humming noise when I decelerate to exactly 30 mph. In addition, I hear a droning/whining noise right at 50 mph.

Any ideas besides the front wheel bearings?

car has 138K miles, tracks straight down the road, and has no steering wheel shimmie.

Response From Discretesignals

You should take it back. Could be they missed something, or maybe even a defective part, which isn't unusual with the cheaper brand of hub bearings.

The droning noises could be from the tires. Cupped or chopped tires can make those noises too. It is also important that the tires are all the same size because that will cause WSS codes to pop up.

Response From ez50nj

noises gone after 2 front hub bearings changed, but abs/trac off/svc eng. soon lights come on quickly when:

1. Back out of driveway in reverse, switch to drive and accelerate
2. Turn wheel full right or full left when engine first started and car not moved

Being that the the car drove perfectly before the hub bearings replaced and the humming and droning noises persisted until the tires were rotated, I conclude that

-The warning lights were not a result of worn hub bearings
-The noise was eliminated by rotating tires side to side on front and rear respectively

***All I can theorize is that looking back in time, we had a sweeping all day rain storm about a month prior to hurricane Sandy. Not a typical vertical downpour, but a swirling nor'easter sweeping rain. I'm wondering if the female leads that plug into the hub got soaked and need to be cleaned and dried out?

***Or, because I have inner wear on both rear tires, could excessive wheel spin from inner rear worn tires triggering the sensors to throw on the lights and DE-activate the ABS and Traction Control?

I'm due for inspection in 2/2013 and will fail inspection with lights on, and want to sell car shortly after, but need lights off, fresh inspection sticker, and functional abs and trac control. Don't want to pour alot of money into car as the paint and body are near perfect and power train is strong. 11 year old Alero presents itself better that most for age and mileage. 2002 GX Coupe with 138K on clock I could hold out for a while and get 2200-2500 if dummy lights off.

Ideas?

Thanks

Response From Sidom

I just breezed thru this so if it has already been mentioned...than.....oops but I'll toss in my 2 cents.....

I know on most GM systems when there is a drivability problem it will automatically disable the traction control & steering stability systems....I see there is a service engine soon light......That needs to be taken care of 1st..

What is the code for the SES?

Response From ez50nj

after 3-4 months with trac off/abs/svc engine soon. Lights are out and car runs fine. Gunning in reverse then forward might be sending stronger signal to abs module? abs humming/activation sometimes kicks on starting out then goes away

Response From Double J Top Rated Answer

Subject: ABS Front Wheel Speed Codes Jumper Harness - kw booster brake C1221 C1222 C1223 C1225 C1226 C1232 C1233 C1252 C1253 caliper DTC EBTCM electrical grab ground hydraulic hydroboost #PI00966B - (04/19/2004)

Models: .


When servicing the vehicle with the VIN you entered, the following diagnosis might be helpful if the vehicle exhibits the described symptoms. Condition/Concern:
91 - 05 JB, NB, or LB vehicles may set any one or a combination of front wheel speed sensor ABS codes as intermittent or hard failures. Recommendation/Instructions:
If after inspection and diagnosis, using the applicable trouble tree(s), the cause of the fault is not readily identified, the most probable cause is often the wheel speed sensor jumper harness. Oftentimes, the harness checks good with the J 39200 fluke meter but will not function correctly when subjected to suspension movement, vibration, and flexing. Seldom will the above condition be corrected by the replacement of the EBCM. The listed part numbers are leads that incorporate a highly flexible "angel hair" that reduces down to standard gauge wire so that it may be properly spliced into the existing circuit. Standard gauge wire should not be used in place of these part numbers.
YEAR
Left
Right
PART NUMBERS BY BODY LINE--J BODY
92
12140077
12140078
93*
12128505
12128504
or 12140077 (Jumper Harness)
or 12140078
***NOTE***93 J-Body had 2 designs available -- a conventional "splice-in" design" or a complete 2-wire jumper harness. Inspect vehicle to determine which design is needed.
94
12128505 jumper harness
12128504 jumper harness
95-05
12187091(same P/N, Left or Right)
Note: Visually Inspect the wheel speed sensor harness connectors and yellow wire to see if it is unseated from the connector. This is especially important on the left hand side. If the wiring is faulty, replace the harness with the above part numbers.
12187091
PART NUMBERS BY BODY LINE - N BODY
91
12091371(same P/N, Left or Right)
12091371
92-98
12140077
12140078
99-05
12167654
12167653
P-90 (97-03 MALIBU/ CUTLASS and 04 CHEV CLASSIC):
97-04
12167654
12167653
PART NUMBERS BY BODY LINE--L BODY
92-96
12140077
12140078
.
Please follow this diagnosis process thoroughly and complete each step. If the condition exhibited is resolved without completing every step, the remaining steps do not need to be performed. If these steps do not resolve the condition, please contact GM TAC for further diagnostic assistance. This diagnostic approach was developed for the vehicle with the VIN you entered and should not be automatically be used for other vehicles with similar symptoms. Models:
(1992-2005 CHEVROLET CAVALIER) and (1992-1994 PONTIAC SUNBIRD) and (1995-2005 PONTIAC SUNFIRE) and (1991-2005 PONTIAC GRAND AM) and (1991 OLDSMOBILE CUTLASS CALAIS) and (1991-1998 BUICK SKYLARK) AND (1992-1998 OLDSMOBILE ACHIEVA) AND (1999-2004 OLDSMOBILE ALERO) AND (1997-2003 CHEVROLET MALIBU) AND (2004 CHEVROLET CLASSIC) AND (1997-1999 OLDSMOBILE CUTLASS) AND (1992-1996 CHEVROLET BERETTA) AND (1992-1996 CHEVROLET CORSICA)
.

Response From ez50nj

new twist. DID NOT replace jumper harness. Just to experiment, I reversed out of driveway aggressively and accelerated hard and lights did not come on. I did get ABS activation/humming while at speed (not braking) for a few days, now it sometimes activates at the end of the trip when I park.

Could be signal disruption from jumper harness to ABS module/ECM? I'm not going to chase it down with $$$ if lights don't come on.

Thoughts?

Response From ez50nj

Great info. Thanks. I'm not mechanically inclined, so if I went to a private shop what do you estimates parts and labor would be to install Jumper Harness?

Interesting new observations/ habits

Lights first came on 2 months ago after first start of day after major rainstorm the night before.When I put car in reverse and turned wheel to left (now activates left or right turn reverse or forward on first turn of day.

Lately, I've tries this experiment: Once lights come on, I drive a few feet, turn off engine, then re-start and the lights stay off for my entire 20 mile trip to work. I stop, put it in park - no lights (ABS/Traction work BTW when lights are off). When I leave work and lights pop on, I do same step. Turn off, re-start and no lights. I make stops at many lights and stop signs on the way home and lights never come on.

THE CRAZY THING IS THAT WHEN I REACH MY DESTINATION (HOME), THE LIGHTS COME ON AS I PULL INTO MY DRIVEWAY BEFORE I STOP CAR AND ENGAGE IN "PARK". It's a slow left turn and uphill, so maybe that's why the lights don't pop on when I'm on the highway ay high speeds making sharp turns.

Is it possible the memory codes remember the incline and surface of my driveway and would trigger lights while car is coasting toward garage???
Again, if I simulate the "coming home driveway incline thing" out on the road I cannot trigger the lights?

Response From ez50nj

new twist:

Lights ALWAYS COME ON first start of day - reverse and turning wheel either way. I researched and tried this:

- seat belt not engaged
-key to 'on' until chime stops
-repeat again twice to 'on' position

Start car - reverse-turn right or left-no lights and ABS and Traction work.

Am I clearing codes with the key in 'on' position 3 times?

Response From Double J

When i read your concern,the first thing that came to mind was the Jumper Harnesses.
We've replaced a ton of them for this type concern.

I'm not saying this is your problem because we're not there to perform any diagnostics on it.

* Your best bet is to take it to your trusted shop and have them diagnose it for you.*
You can mention the TSB to your shop,maybe they didn't check for bulletins and aren't aware of it.
Maybe they did and it doesn't apply

Do you know what codes are being set?

If you're looking for an internet diagnosis,then replace the Jumper harnesses.
They are a known problem.

I know what approx. it should go for but i wont say,i'll let the shop tell you what they expect for the repair.
You can always call around for estimates.

Response From ez50nj

You're theory and the TSB sound about right. I'm in no rush to do it until I sell the car next spring. Thanks for the feedback!

Response From Tom Greenleaf

If these tires are that screwed up they alone can and will cause ABS/Trac Control to get lousy input. Plain rain mentioned even hard and driven unless it flooded the car should dry out.

Tires may still be legal for wear but have to match. Seems they have already caused hub/bearings to be blamed so pay attention to tires. No feature a vehicle can have for traction for stopping, steering or going can be any better than the tires that touch the road,

T

Response From ez50nj

paragraph 2--you hit it on the head. Brought it back. Had codes. I asked them to swap two front tires and two rear tires (not front to rear, just left to right swap on front and rear). Droning gone at 50 mph/wobble noise at 30 gone. No Trac off or ABS lights on. One of the L/R tires has minor inner wear and cupping so that might have triggered an "excessive wheel spin code"

Thanks for the feedback!