802.589.0911 Live Chat With Us

Shop By Brand

The Following brands are available based on your search.

  • Cardone
    Cardone
  • Surtrak Axle
    Surtrak Axle

Showing Products For 2005 Chevrolet Uplander CV Axle Shaft

Below are all the different brands and applications for 2005 Chevrolet Uplander CV Axle Shaft

Showing 1 - 10 of 13 Products for CV Axle Shaft.

Refine Your Search

Cardone
2005 Chevrolet Uplander CV Axle Shaft - Front Left Cardone - Reman. A-1 CARDONE Constant Velocity Drive Axle

P311-410927B    60-1344  Remanufactured

26075600 , 89047673 , 26075602

Qty:
$65.42
Cardone CV Axle Shaft  Front Left
  • Remanufactured Constant Velocity Drive Axle
  • Reman. A-1 CARDONE Constant Velocity Drive Axle
  • Product Attributes:
    • Axle Nut Locking Type: Self Lock
    • Compressed Length: 22 3/8"
    • FAQs:
      • Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly.
      • Are The Cv Drive Axle Shafts Balanced At The Factory?
      • Can I Let The Cv Drive Axles Hang While I Am Working On The Car?
      • I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?
      • I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?
      • I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?
      • Is It Ok To Use An Impact Hammer To Install The Retaining Nut?
      • Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint.
      • Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications.
      • No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One.
      • Shafts Are Inspected 100% For Run Out To Prevent Vibrations.  Only Shafts That Meet The Specifications For Run Out Are Utilized In The Remanufacturing Of A Cv Drive Axle Assembly.
      • The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?
      • The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load.  This Is Typically An Outboard Joint Problem.
      • The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced.
      • The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up.
      • The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint.
      • The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut.  Should I Reuse It?
      • The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time.
      • The Wheels Wobble When I Make A Turn. What's The Problem?
      • When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?
      • When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?
      • When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?
      • When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking.
      • When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On.
    • Features and Benefits:
      • 100% Neoprene Boots Ensure Excellent Environmental Stress Resistance, Which Eliminates Cracking, A Leading Cause Of Boot Failure.
      • Boot Clamps Are Pneumatically Crimped Creating A Perfect Seal Between The Boot And Housing.
      • Cv Drive Axle Is Measured 100% After Assembly To Ensure Proper Fit.
      • Cv Drive Axle Shafts Are Inspected 100% For Run Out To Prevent Vibrations.
      • High-quality Grease Withstands High-temperature And Pressure Extremes, Which Extends Joint Life.
      • High-tech Grinding Machines Maintain The Original Design Of The Outer Housing, Race And Cage To Guarantee Reliable Performance.
      • Splines Are Chased 100% To Ensure Proper Fit Of The Axle Into The Mating Hub And Transmission, Which Eliminates Installation Hassles.
    • Input Shaft Connection Style: Spline
    • Output Shaft Connection Style: Spline
    • Product Condition: Remanufactured
    • Spindle Nut Hex Head Size: 34mm
    • Spindle Nut Thread Size: M27 X 2.0
  • CARDONE has extensive experience in remanufacturing CV Drive Axles – we’ve spent over two decades re-engineering materials and processes to arrive at a superior, longer-lasting product. Our proprietary pneumatic clamping machines create a perfect seal between the boot and housing, creating a water-tight seal. The perfect geometry of the ball groove is maintained to allow for proper grease flow, significantly increasing longevity. Additionally, all CV Drive Axle shafts are individually verified for straightness, resulting in vibration-free performance at all speeds.
Brand: Cardone
Position: Front Left
Additional Fitment Information:
Vehicle Drive Type Position
2005 - Chevrolet Uplander AWD Front Left
Cardone
2005 Chevrolet Uplander CV Axle Shaft - Front Right Cardone - Reman. A-1 CARDONE Constant Velocity Drive Axle

P311-4A4486D    60-1445  Remanufactured

19153645 , 89060224 , 88964159

Qty:
$60.22
Cardone CV Axle Shaft  Front Right
  • Remanufactured Constant Velocity Drive Axle
  • Reman. A-1 CARDONE Constant Velocity Drive Axle
  • Product Attributes:
    • Axle Nut Locking Type: Self Lock
    • Compressed Length: 25 1/4"
    • FAQs:
      • Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly.
      • Are The Cv Drive Axle Shafts Balanced At The Factory?
      • Can I Let The Cv Drive Axles Hang While I Am Working On The Car?
      • I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?
      • I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?
      • I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?
      • Is It Ok To Use An Impact Hammer To Install The Retaining Nut?
      • Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint.
      • Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications.
      • No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One.
      • Shafts Are Inspected 100% For Run Out To Prevent Vibrations.  Only Shafts That Meet The Specifications For Run Out Are Utilized In The Remanufacturing Of A Cv Drive Axle Assembly.
      • The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?
      • The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load.  This Is Typically An Outboard Joint Problem.
      • The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced.
      • The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up.
      • The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint.
      • The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut.  Should I Reuse It?
      • The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time.
      • The Wheels Wobble When I Make A Turn. What's The Problem?
      • When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?
      • When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?
      • When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?
      • When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking.
      • When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On.
    • Features and Benefits:
      • Boot Clamps Are Pneumatically Crimped Creating A Perfect Seal Between The Boot And Housing.
      • Cv Drive Axle Is Measured 100% After Assembly To Ensure Proper Fit.
      • Cv Drive Axle Shafts Are Inspected 100% For Run Out To Prevent Vibrations.
      • High-quality Grease Withstands High-temperature And Pressure Extremes, Which Extends Joint Life.
      • High-tech Grinding Machines Maintain The Original Design Of The Outer Housing, Race And Cage To Guarantee Reliable Performance.
      • Splines Are Chased 100% To Ensure Proper Fit Of The Axle Into The Mating Hub And Transmission, Which Eliminates Installation Hassles.
      • Threads Are Chased 100% To Ensure Proper Fit Of The New Retaining Nut Supplied With Each Cv Drive Axle.
    • Input Shaft Connection Style: Spline
    • Output Shaft Connection Style: Spline
    • Product Condition: Remanufactured
    • Spindle Nut Hex Head Size: 34mm
    • Spindle Nut Thread Size: M27 X 2.0
  • CARDONE has extensive experience in remanufacturing CV Drive Axles – we’ve spent over two decades re-engineering materials and processes to arrive at a superior, longer-lasting product. Our proprietary pneumatic clamping machines create a perfect seal between the boot and housing, creating a water-tight seal. The perfect geometry of the ball groove is maintained to allow for proper grease flow, significantly increasing longevity. Additionally, all CV Drive Axle shafts are individually verified for straightness, resulting in vibration-free performance at all speeds.
Brand: Cardone
Position: Front Right
Additional Fitment Information:
Vehicle Drive Type Position
2005 - Chevrolet Uplander FWD Front Right
Cardone
2005 Chevrolet Uplander CV Axle Shaft - Rear Right Cardone - Reman. A-1 CARDONE Constant Velocity Drive Axle

P311-306AC89    60-1202  Remanufactured

88967242 , 10424907

Qty:
$65.42
Cardone CV Axle Shaft  Rear Right
  • Remanufactured Constant Velocity Drive Axle
  • Reman. A-1 CARDONE Constant Velocity Drive Axle
  • Product Attributes:
    • Axle Nut Locking Type: Self Lock
    • Compressed Length: 32"
    • FAQs:
      • Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly.
      • Are The Cv Drive Axle Shafts Balanced At The Factory?
      • Can I Let The Cv Drive Axles Hang While I Am Working On The Car?
      • I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?
      • I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?
      • I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?
      • Is It Ok To Use An Impact Hammer To Install The Retaining Nut?
      • Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint.
      • Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications.
      • No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One.
      • Shafts Are Inspected 100% For Run Out To Prevent Vibrations.  Only Shafts That Meet The Specifications For Run Out Are Utilized In The Remanufacturing Of A Cv Drive Axle Assembly.
      • The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?
      • The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load.  This Is Typically An Outboard Joint Problem.
      • The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced.
      • The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up.
      • The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint.
      • The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut.  Should I Reuse It?
      • The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time.
      • The Wheels Wobble When I Make A Turn. What's The Problem?
      • When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?
      • When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?
      • When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?
      • When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking.
      • When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On.
    • Features and Benefits:
      • Boot Clamps Are Pneumatically Crimped Creating A Perfect Seal Between The Boot And Housing.
      • Cv Drive Axle Is Measured 100% After Assembly To Ensure Proper Fit.
      • Cv Drive Axle Shafts Are Inspected 100% For Run Out To Prevent Vibrations.
      • High-quality Grease Withstands High-temperature And Pressure Extremes, Which Extends Joint Life.
      • High-tech Grinding Machines Maintain The Original Design Of The Outer Housing, Race And Cage To Guarantee Reliable Performance.
      • Splines Are Chased 100% To Ensure Proper Fit Of The Axle Into The Mating Hub And Transmission, Which Eliminates Installation Hassles.
      • Threads Are Chased 100% To Ensure Proper Fit Of The New Retaining Nut Supplied With Each Cv Drive Axle.
    • Input Shaft Connection Style: Spline
    • Output Shaft Connection Style: Spline
    • Product Condition: Remanufactured
    • Spindle Nut Hex Head Size: 34mm
    • Spindle Nut Thread Size: M27 X 2.0
  • CARDONE has extensive experience in remanufacturing CV Drive Axles – we’ve spent over two decades re-engineering materials and processes to arrive at a superior, longer-lasting product. Our proprietary pneumatic clamping machines create a perfect seal between the boot and housing, creating a water-tight seal. The perfect geometry of the ball groove is maintained to allow for proper grease flow, significantly increasing longevity. Additionally, all CV Drive Axle shafts are individually verified for straightness, resulting in vibration-free performance at all speeds.
Brand: Cardone
Position: Rear Right
Additional Fitment Information:
Vehicle Drive Type Position
2005 - Chevrolet Uplander AWD Rear Right
Cardone
2005 Chevrolet Uplander CV Axle Shaft - Rear Left Cardone - Reman. A-1 CARDONE Constant Velocity Drive Axle

P311-306AC89    60-1202  Remanufactured

88967242 , 10424907

Qty:
$65.42
Cardone CV Axle Shaft  Rear Left
  • Remanufactured Constant Velocity Drive Axle
  • Reman. A-1 CARDONE Constant Velocity Drive Axle
  • Product Attributes:
    • Axle Nut Locking Type: Self Lock
    • Compressed Length: 32"
    • FAQs:
      • Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly.
      • Are The Cv Drive Axle Shafts Balanced At The Factory?
      • Can I Let The Cv Drive Axles Hang While I Am Working On The Car?
      • I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?
      • I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?
      • I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?
      • Is It Ok To Use An Impact Hammer To Install The Retaining Nut?
      • Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint.
      • Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications.
      • No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One.
      • Shafts Are Inspected 100% For Run Out To Prevent Vibrations.  Only Shafts That Meet The Specifications For Run Out Are Utilized In The Remanufacturing Of A Cv Drive Axle Assembly.
      • The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?
      • The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load.  This Is Typically An Outboard Joint Problem.
      • The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced.
      • The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up.
      • The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint.
      • The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut.  Should I Reuse It?
      • The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time.
      • The Wheels Wobble When I Make A Turn. What's The Problem?
      • When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?
      • When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?
      • When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?
      • When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking.
      • When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On.
    • Features and Benefits:
      • Boot Clamps Are Pneumatically Crimped Creating A Perfect Seal Between The Boot And Housing.
      • Cv Drive Axle Is Measured 100% After Assembly To Ensure Proper Fit.
      • Cv Drive Axle Shafts Are Inspected 100% For Run Out To Prevent Vibrations.
      • High-quality Grease Withstands High-temperature And Pressure Extremes, Which Extends Joint Life.
      • High-tech Grinding Machines Maintain The Original Design Of The Outer Housing, Race And Cage To Guarantee Reliable Performance.
      • Splines Are Chased 100% To Ensure Proper Fit Of The Axle Into The Mating Hub And Transmission, Which Eliminates Installation Hassles.
      • Threads Are Chased 100% To Ensure Proper Fit Of The New Retaining Nut Supplied With Each Cv Drive Axle.
    • Input Shaft Connection Style: Spline
    • Output Shaft Connection Style: Spline
    • Product Condition: Remanufactured
    • Spindle Nut Hex Head Size: 34mm
    • Spindle Nut Thread Size: M27 X 2.0
  • CARDONE has extensive experience in remanufacturing CV Drive Axles – we’ve spent over two decades re-engineering materials and processes to arrive at a superior, longer-lasting product. Our proprietary pneumatic clamping machines create a perfect seal between the boot and housing, creating a water-tight seal. The perfect geometry of the ball groove is maintained to allow for proper grease flow, significantly increasing longevity. Additionally, all CV Drive Axle shafts are individually verified for straightness, resulting in vibration-free performance at all speeds.
Brand: Cardone
Position: Rear Left
Additional Fitment Information:
Vehicle Drive Type Position
2005 - Chevrolet Uplander AWD Rear Left
Cardone
2005 Chevrolet Uplander CV Axle Shaft - Front Left Cardone - New CARDONE SELECT Constant Velocity Drive Axle

P311-05F448F    66-1444  New

10399693 , 19153644 , 26075602 , 20859673 , 10424906 , 89047673 , 26075600

Qty:
$63.76
Cardone CV Axle Shaft  Front Left
  • New Constant Velocity Drive Axle
  • New CARDONE SELECT Constant Velocity Drive Axle
  • Product Attributes:
    • Axle Nut Locking Type: Self Lock
    • Compressed Length: 22 1/2"
    • FAQs:
      • Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly.
      • Can I Let The Cv Drive Axles Hang While I Am Working On The Car?
      • I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?
      • I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?
      • I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?
      • Is It Ok To Use An Impact Hammer To Install The Retaining Nut?
      • Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint.
      • Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications.
      • No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One.
      • The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?
      • The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load.  This Is Typically An Outboard Joint Problem.
      • The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced.
      • The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up.
      • The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint.
      • The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut.  Should I Reuse It?
      • The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time.
      • The Wheels Wobble When I Make A Turn. What's The Problem?
      • When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?
      • When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?
      • When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?
      • When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking.
      • When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On.
    • Features and Benefits:
      • A New Cv Drive Axle Retaining Nut Is Supplied With Every Unit For A Hassle-free Installation, Due To The Likelihood Of The Original Retaining Nut Being Worn Or Stripped.
      • Boot Clamps Are Pneumatically Crimped Creating A Perfect Seal Between The Boot And Housing.
      • Cv Drive Axle Measurements Are Validated 100% After Assembly To Ensure A Proper Fit.
      • High-quality Grease Withstands High-temperature And High-torque Demands To Ensure Long-lasting, Reliable Performance.
      • Neoprene Boots Are Designed With Additional Bellows, When Needed, To Resist Bellow Stress And Cracking Due To Environment, Which Is The Leading Cause Of Boot Failure.
      • Proprietary Engineering Processes Ensure That All Cv Drive Axles Meet O.e. Form, Fit And Function.
      • Severe-duty Cv Drive Axles Include A Thermoplastic Outboard Boot For Increased Life And Durability Versus A Traditional Neoprene Boot.
      • Splines Are Precision Rolled To Ensure Proper Fit Of Cv Drive Axle Into The Mating Hub And Transmission, Which Eliminates Installation Hassles.
      • Threads Are Precision Rolled To Ensure Proper Fit When Axle Nut Is Installed.
    • Input Shaft Connection Style: Spline
    • Output Shaft Connection Style: Spline
    • Product Condition: New
    • Spindle Nut Hex Head Size: 34mm
    • Spindle Nut Thread Size: M24 X 2.0
  • CARDONE has extensive experience in testing and engineering CV Drive Axles – we’ve spent over two decades analyzing materials and processes to arrive at a superior, longer-lasting product. CARDONE Engineered Technology is our proprietary method of arriving at a product that meets O.E. performance standards. 100% Neoprene boots are designed with additional bellows, when needed, to resist bellow stress and ozone cracking, the leading cause of boot failure. Additionally, all CV Drive Axle shafts are individually verified for straightness, resulting in vibration-free performance at all speeds.
Brand: Cardone
Position: Front Left
Additional Fitment Information:
Vehicle Drive Type Position
2005 - Chevrolet Uplander AWD Front Left
Cardone
2005 Chevrolet Uplander CV Axle Shaft - Front Right Cardone - New CARDONE SELECT Constant Velocity Drive Axle

P311-0AF1526    66-1445  New

19153645 , 10424904 , 88964159

Qty:
$59.14
Cardone CV Axle Shaft  Front Right
  • New Constant Velocity Drive Axle
  • New CARDONE SELECT Constant Velocity Drive Axle
  • Product Attributes:
    • Axle Nut Locking Type: Self Lock
    • Compressed Length: 25 1/4"
    • FAQs:
      • Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly.
      • Can I Let The Cv Drive Axles Hang While I Am Working On The Car?
      • I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?
      • I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?
      • I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?
      • Is It Ok To Use An Impact Hammer To Install The Retaining Nut?
      • Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint.
      • Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications.
      • No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One.
      • The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?
      • The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load.  This Is Typically An Outboard Joint Problem.
      • The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced.
      • The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up.
      • The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint.
      • The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut.  Should I Reuse It?
      • The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time.
      • The Wheels Wobble When I Make A Turn. What's The Problem?
      • When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?
      • When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?
      • When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?
      • When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking.
      • When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On.
    • Features and Benefits:
      • A New Cv Drive Axle Retaining Nut Is Supplied With Every Unit For A Hassle-free Installation, Due To The Likelihood Of The Original Retaining Nut Being Worn Or Stripped.
      • Boot Clamps Are Pneumatically Crimped Creating A Perfect Seal Between The Boot And Housing.
      • Cv Drive Axle Measurements Are Validated 100% After Assembly To Ensure A Proper Fit.
      • High-quality Grease Withstands High-temperature And High-torque Demands To Ensure Long-lasting, Reliable Performance.
      • Neoprene Boots Are Designed With Additional Bellows, When Needed, To Resist Bellow Stress And Cracking Due To Environment, Which Is The Leading Cause Of Boot Failure.
      • Proprietary Engineering Processes Ensure That All Cv Drive Axles Meet O.e. Form, Fit And Function.
      • Severe-duty Cv Drive Axles Include A Thermoplastic Outboard Boot For Increased Life And Durability Versus A Traditional Neoprene Boot.
      • Splines Are Precision Rolled To Ensure Proper Fit Of Cv Drive Axle Into The Mating Hub And Transmission, Which Eliminates Installation Hassles.
      • Threads Are Precision Rolled To Ensure Proper Fit When Axle Nut Is Installed.
    • Input Shaft Connection Style: Spline
    • Output Shaft Connection Style: Spline
    • Product Condition: New
    • Spindle Nut Hex Head Size: 34mm
    • Spindle Nut Thread Size: M24 X 2.0
  • CARDONE has extensive experience in testing and engineering CV Drive Axles – we’ve spent over two decades analyzing materials and processes to arrive at a superior, longer-lasting product. CARDONE Engineered Technology is our proprietary method of arriving at a product that meets O.E. performance standards. 100% Neoprene boots are designed with additional bellows, when needed, to resist bellow stress and ozone cracking, the leading cause of boot failure. Additionally, all CV Drive Axle shafts are individually verified for straightness, resulting in vibration-free performance at all speeds.
Brand: Cardone
Position: Front Right
Additional Fitment Information:
Vehicle Drive Type Position
2005 - Chevrolet Uplander FWD Front Right
Cardone
2005 Chevrolet Uplander CV Axle Shaft - Rear Left Cardone - New CARDONE SELECT Constant Velocity Drive Axle

P311-175CA57    66-1202  New

10424907 , 88967242

Qty:
$70.84
Cardone CV Axle Shaft  Rear Left
  • New Constant Velocity Drive Axle
  • New CARDONE SELECT Constant Velocity Drive Axle
  • Product Attributes:
    • Axle Nut Locking Type: Self Lock
    • Compressed Length: 31 1/4"
    • FAQs:
      • Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly.
      • Can I Let The Cv Drive Axles Hang While I Am Working On The Car?
      • I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?
      • I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?
      • I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?
      • Is It Ok To Use An Impact Hammer To Install The Retaining Nut?
      • Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint.
      • Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications.
      • No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One.
      • The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?
      • The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load.  This Is Typically An Outboard Joint Problem.
      • The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced.
      • The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up.
      • The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint.
      • The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut.  Should I Reuse It?
      • The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time.
      • The Wheels Wobble When I Make A Turn. What's The Problem?
      • When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?
      • When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?
      • When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?
      • When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking.
      • When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On.
    • Features and Benefits:
      • A New Cv Drive Axle Retaining Nut Is Supplied With Every Unit For A Hassle-free Installation, Due To The Likelihood Of The Original Retaining Nut Being Worn Or Stripped.
      • Boot Clamps Are Pneumatically Crimped Creating A Perfect Seal Between The Boot And Housing.
      • Cv Drive Axle Measurements Are Validated 100% After Assembly To Ensure A Proper Fit.
      • High-quality Grease Withstands High-temperature And High-torque Demands To Ensure Long-lasting, Reliable Performance.
      • Neoprene Boots Are Designed With Additional Bellows, When Needed, To Resist Bellow Stress And Cracking Due To Environment, Which Is The Leading Cause Of Boot Failure.
      • Proprietary Engineering Processes Ensure That All Cv Drive Axles Meet O.e. Form, Fit And Function.
      • Severe-duty Cv Drive Axles Include A Thermoplastic Outboard Boot For Increased Life And Durability Versus A Traditional Neoprene Boot.
      • Splines Are Precision Rolled To Ensure Proper Fit Of Cv Drive Axle Into The Mating Hub And Transmission, Which Eliminates Installation Hassles.
      • Threads Are Precision Rolled To Ensure Proper Fit When Axle Nut Is Installed.
    • Input Shaft Connection Style: Spline
    • Output Shaft Connection Style: Spline
    • Product Condition: New
    • Spindle Nut Hex Head Size: 34mm
    • Spindle Nut Thread Size: M27 X 2.0
  • CARDONE has extensive experience in testing and engineering CV Drive Axles – we’ve spent over two decades analyzing materials and processes to arrive at a superior, longer-lasting product. CARDONE Engineered Technology is our proprietary method of arriving at a product that meets O.E. performance standards. 100% Neoprene boots are designed with additional bellows, when needed, to resist bellow stress and ozone cracking, the leading cause of boot failure. Additionally, all CV Drive Axle shafts are individually verified for straightness, resulting in vibration-free performance at all speeds.
Brand: Cardone
Position: Rear Left
Additional Fitment Information:
Vehicle Drive Type Position
2005 - Chevrolet Uplander AWD Rear Left
Cardone
2005 Chevrolet Uplander CV Axle Shaft - Rear Right Cardone - New CARDONE SELECT Constant Velocity Drive Axle

P311-175CA57    66-1202  New

10424907 , 88967242

Qty:
$70.84
Cardone CV Axle Shaft  Rear Right
  • New Constant Velocity Drive Axle
  • New CARDONE SELECT Constant Velocity Drive Axle
  • Product Attributes:
    • Axle Nut Locking Type: Self Lock
    • Compressed Length: 31 1/4"
    • FAQs:
      • Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly.
      • Can I Let The Cv Drive Axles Hang While I Am Working On The Car?
      • I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?
      • I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?
      • I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?
      • Is It Ok To Use An Impact Hammer To Install The Retaining Nut?
      • Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint.
      • Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications.
      • No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One.
      • The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?
      • The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load.  This Is Typically An Outboard Joint Problem.
      • The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced.
      • The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up.
      • The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint.
      • The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut.  Should I Reuse It?
      • The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time.
      • The Wheels Wobble When I Make A Turn. What's The Problem?
      • When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?
      • When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?
      • When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?
      • When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking.
      • When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On.
    • Features and Benefits:
      • A New Cv Drive Axle Retaining Nut Is Supplied With Every Unit For A Hassle-free Installation, Due To The Likelihood Of The Original Retaining Nut Being Worn Or Stripped.
      • Boot Clamps Are Pneumatically Crimped Creating A Perfect Seal Between The Boot And Housing.
      • Cv Drive Axle Measurements Are Validated 100% After Assembly To Ensure A Proper Fit.
      • High-quality Grease Withstands High-temperature And High-torque Demands To Ensure Long-lasting, Reliable Performance.
      • Neoprene Boots Are Designed With Additional Bellows, When Needed, To Resist Bellow Stress And Cracking Due To Environment, Which Is The Leading Cause Of Boot Failure.
      • Proprietary Engineering Processes Ensure That All Cv Drive Axles Meet O.e. Form, Fit And Function.
      • Severe-duty Cv Drive Axles Include A Thermoplastic Outboard Boot For Increased Life And Durability Versus A Traditional Neoprene Boot.
      • Splines Are Precision Rolled To Ensure Proper Fit Of Cv Drive Axle Into The Mating Hub And Transmission, Which Eliminates Installation Hassles.
      • Threads Are Precision Rolled To Ensure Proper Fit When Axle Nut Is Installed.
    • Input Shaft Connection Style: Spline
    • Output Shaft Connection Style: Spline
    • Product Condition: New
    • Spindle Nut Hex Head Size: 34mm
    • Spindle Nut Thread Size: M27 X 2.0
  • CARDONE has extensive experience in testing and engineering CV Drive Axles – we’ve spent over two decades analyzing materials and processes to arrive at a superior, longer-lasting product. CARDONE Engineered Technology is our proprietary method of arriving at a product that meets O.E. performance standards. 100% Neoprene boots are designed with additional bellows, when needed, to resist bellow stress and ozone cracking, the leading cause of boot failure. Additionally, all CV Drive Axle shafts are individually verified for straightness, resulting in vibration-free performance at all speeds.
Brand: Cardone
Position: Rear Right
Additional Fitment Information:
Vehicle Drive Type Position
2005 - Chevrolet Uplander AWD Rear Right
Surtrak Axle
2005 Chevrolet Uplander CV Axle Shaft - Front Left Surtrak Axle

P311-12D349C    GM-8153  New

949083 , 88964160 , MX-16284 , 80-5844 , 26075602 , 60-1344 , GM-6279 , 706103 , 26073391 , 60-1444 , AX-8482 , PO10501 , 80-5077 , MX-16279 , 10047N , MP1344 , 70297 , 410370 , 92737 , 95844 , 179153 , 80-1830 , 959303 , 1444N , GM10513 , NCV10218 , GC-8-8681 , 19153644 , 66-1444 , MP-1344 , AX-6103

Qty:
$63.15
Surtrak Axle CV Axle Shaft  Front Left
  • CV Axle Shaft
  • Product Attributes:
    • ABS Ring Tooth Count: N/a
    • ABS Ring Type: N/a
    • Axle Bolt Hex Size (mm): N/a
    • Axle Bolt Length (mm): N/a
    • Axle Bolt Thread Size: N/a
    • Axle Nut Head Type: Hex
    • Axle Nut Height (in): 6/7
    • Axle Nut Hex Size (in): 1 2/7
    • Axle Nut Hex Size (mm): 32.8
    • Axle Nut Length (in): 1 1/2
    • Axle Nut Length (mm): 37.9
    • Axle Nut Locking Type: Self-lock
    • Axle Nut Thread Size: M27*2
    • Boot Material: Neoprene
    • Inboard Bolt Head Size (in): N/a
    • Inboard Bolt Head Size (mm): N/a
    • Inboard Bolt Head Type: N/a
    • Inboard Bolt Length (in): N/a
    • Inboard Bolt Length (mm): N/a
    • Inboard Bolt Thread Size: N/a
    • Inboard Joint Type: Female
    • Inboard Shaft Connection Style: Female
    • New Or Remanufactured: New
    • Number Of Bolt Holes: N/a
    • Number Of Inboard Joint Bolt Holes: N/a
    • Number Of Inboard Shaft Bolts: N/a
    • Number Of Outboard Joint Bolt Holes: N/a
    • Number Of Outboard Shaft Bolts: N/a
    • Outboard Bolt Head Size (in): N/a
    • Outboard Bolt Head Size (mm): N/a
    • Outboard Bolt Head Type: N/a
    • Outboard Bolt Length (in): N/a
    • Outboard Bolt Length (mm): N/a
    • Outboard Joint Bolt Thread Size: N/a
    • Overall Compressed Length (in): 22.36
    • Overall Compressed Length (mm): 568
  • Limited Lifetime Warranty; ABS axles fit non-ABS applications unless otherwise noted; ISO 9001:1007 and TS 16949:2009 Certified Company
Brand: Surtrak Axle
Position: Front Left
Additional Fitment Information:
Vehicle Drive Type Position
2005 - Chevrolet Uplander FWD Front Left
Surtrak Axle
2005 Chevrolet Uplander CV Axle Shaft - Front Right Surtrak Axle

P311-4A0CC2E    GM-8159  New

10424904 , 80-1518 , GM-6102 , CV3908 , NCV10243 , 949089 , 9438 , 1294N , 95098 , 706076 , 60-1445 , 706102 , CV5406 , GC-8-8682 , 959318 , 60-1367 , AX-1876 , 1467N , 92738 , 40-16102 , 179159 , 66-1445 , 19153645 , 9438N , MP-1367 , 9439 , 88964159 , MX-16102 , MP1367 , 80-1876 , 411528 , 70591 , GM10514 , GM-2096 , AX-6102

Qty:
$53.30
Surtrak Axle CV Axle Shaft  Front Right
  • CV Axle Shaft
  • Product Attributes:
    • ABS Ring Tooth Count: N/a
    • ABS Ring Type: N/a
    • Axle Bolt Hex Size (mm): N/a
    • Axle Bolt Length (mm): N/a
    • Axle Bolt Thread Size: N/a
    • Axle Nut Head Type: Hex
    • Axle Nut Height (in): 6/7
    • Axle Nut Hex Size (in): 1 2/7
    • Axle Nut Hex Size (mm): 32.8
    • Axle Nut Length (in): 1 1/2
    • Axle Nut Length (mm): 37.9
    • Axle Nut Locking Type: Self-lock
    • Axle Nut Thread Size: M27*2
    • Boot Material: Neoprene
    • Inboard Bolt Head Size (in): N/a
    • Inboard Bolt Head Size (mm): N/a
    • Inboard Bolt Head Type: N/a
    • Inboard Bolt Length (in): N/a
    • Inboard Bolt Length (mm): N/a
    • Inboard Bolt Thread Size: N/a
    • New Or Remanufactured: New
    • Number Of Bolt Holes: N/a
    • Number Of Inboard Joint Bolt Holes: N/a
    • Number Of Inboard Shaft Bolts: N/a
    • Number Of Outboard Joint Bolt Holes: N/a
    • Number Of Outboard Shaft Bolts: N/a
    • Outboard Bolt Head Size (in): N/a
    • Outboard Bolt Head Size (mm): N/a
    • Outboard Bolt Head Type: N/a
    • Outboard Bolt Length (in): N/a
    • Outboard Bolt Length (mm): N/a
    • Outboard Joint Bolt Thread Size: N/a
    • Overall Compressed Length (in): 25.63
    • Overall Compressed Length (mm): 651
  • Limited Lifetime Warranty; ABS axles fit non-ABS applications unless otherwise noted; ISO 9001:1007 and TS 16949:2009 Certified Company
Brand: Surtrak Axle
Position: Front Right
Additional Fitment Information:
Vehicle Drive Type Position
2005 - Chevrolet Uplander FWD Front Right

Showing 1 - 10 of 13 Products for CV Axle Shaft.