Shop By Brand

The Following brands are available based on your search.

  • ACDelco
    ACDelco
  • Cardone
    Cardone
  • Centric
    Centric
  • Dorman
    Dorman
  • Dynamic Friction
    Dynamic Friction
  • Motorcraft
    Motorcraft
  • Raybestos
    Raybestos

Showing Products For 2004 Mercury Sable Brake Master Cylinder

Below are all the different brands and applications for 2004 Mercury Sable Brake Master Cylinder

Showing 1 - 10 of 22 Products for Brake Master Cylinder.

Refine Your Search

Dynamic Friction
2004 Mercury Sable Brake Master Cylinder Dynamic Friction - DFC Brake Master Cylinder

P311-45FA70E    355-54084  New

Qty:
70.99
Dynamic Friction Brake Master Cylinder
  • DFC Master Cylinder
  • ; T/C
  • DFC Brake Master Cylinder
Brand: Dynamic Friction
Additional Fitment Information:
Vehicle
2004 - Mercury Sable
Dynamic Friction
2004 Mercury Sable Brake Master Cylinder Dynamic Friction - DFC Brake Master Cylinder

P311-1B54394    355-54069  New

Qty:
61.45
Dynamic Friction Brake Master Cylinder
  • DFC Master Cylinder
  • ; To 7/03 Except T/C
  • DFC Brake Master Cylinder
Brand: Dynamic Friction
Additional Fitment Information:
Vehicle
2004 - Mercury Sable
Cardone
2004 Mercury Sable Brake Master Cylinder Cardone - Brake Master Cylinder

P311-1D26760    13-3029  New

4F1Z2140BA

Qty:
83.69
Cardone Brake Master Cylinder
  • with Traction Control Reservoir Included
  • Brake Master Cylinder
  • Product Attributes:
    • Bore Diameter (N): 1.000"
    • E-Waste: No
    • FAQs:
      • As A Rule, Always Use The Brake Fluid Recommended By The O.e. Which Is Stamped On The Master Cylinder Lid. Note: Always Use New Fluid From A Sealed Container.
      • Check Booster For A Defective Push Rod Seal. If This Seal Is Bad, It Could Drain The Brake Fluid Out Of The Master Cylinder.
      • Check The Steering And Suspension. Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Check Brake Lining For Oil/grease Or Uneven Wear. Inspect Brake Hoses For Restriction. Check For Proper Tire Pressure.
      • Does A Step Bore Style Master Cylinder Require A Specific Bleeding Process?
      • Dot 3 And 4 Are Glycol-based Fluids And Dot 5 Is A Silicone-based Fluid.
      • First, Check For Air In The System. Make Sure Master Cylinder Is Level When Bleeding. Air Will Compress In A Hydraulic System Causing A Low Pedal. Then, Check For Brake Hose Swelling Or Expanding Under Pressure. Next, Check Brake Drums/discs For Proper Sp
      • How Can I Test A Master Cylinder To See If It's Bypassing?
      • I Replaced The Master Cylinder And Now The Pedal Is High And Hard. Why?
      • Most Likely, The Fluid In The System Is Contaminated. The Most Common Form Of Contamination Occurs When Petroleum-based Fluid Has Been Accidentally Introduced Into The Brake System. If That Has Happened It Is Almost Certain That All Rubber Components In T
      • My Original Master Cylinder Leaked Out Of The Back Of The Piston Into The Booster Area. Why?
      • One Side Of My Front Brakes Won’t Release, Why?
      • Replace All Brake Fluid. Brake Fluid Is Hygroscopic Which Means It Absorbs Moisture. Too Much Water In Brake Fluid Will Cause Vapor Lock And Apply Pressure To The Wheels. Also Check For Proper Push Rod Adjustments And Stop Light/cruise Control Switch Adju
      • Simply Plug The Master Cylinder Ports And Press The Brake Pedal. If The Master Cylinder Is Bypassing, The Pedal Will Go Down. If The Pedal Stops Hard, The Master Cylinder Is Ok.
      • The Brake Pedal Is Low And Spongy. Is It A Bad Master Cylinder?
      • The First Step To Bench Bleeding A Step Bore Is To Slowly Depress The Master Cylinder Piston, Then Release Slowly And Wait 20 Seconds Before Depressing Again. Never Pump Piston/pedal With A Step Bore Style Master Cylinder. Follow The Same Process On The V
      • The Master Cylinder Is Working Correctly. Check For A Faulty Brake Booster Or Frozen Wheel Cylinder/caliper.
      • This Is Caused By A Problem With The Caliper Or A Brake Hose.
      • What Causes The Brakes To Lock Up After Only A Couple Of Miles?
      • What Causes The Car To Pull To One Side During Braking?
      • What Type Of Fluid Should I Use: Dot 3, Dot 4 Or Dot 5?
      • What’s The Difference Between Dot 3, 4 And 5?
      • Why Is The Piston Stuck Inside The Bore Of My Master Cylinder?
    • Features and Benefits:
      • Bores Meet Critical Micro-finish Specifications To Eliminate Pitting And Corrosion, A Cause Of Premature Failure
      • Castings Feature A Premium Protective Coating To Minimize Corrosion And Extend Unit Life
      • Mounting Hardware And Bleeding Kits Are Supplied With Every Unit To Make The Installation And Bleeding Process Faster And Easier (where Applicable)
      • Only O.e.-quality Seals And Cups Are Used To Ensure O.e. Performance And Reliability. All Rubber Components Meet S.a.e. Specifications
      • Plastic Reservoirs Are Vacuum-tested To Ensure They Are Leak Free
      • Seals Are Temperature-cycled From -30°f To +220°f To Ensure Reliable Performance During Your Daily Commute
    • First Application Year: 2004
    • Installation Hardware Included: No
    • Master Cylinder Color/Finish: Gray
    • Master Cylinder Material: Aluminum
    • Mounting Hole Quantity: 2
    • Pedal Rod Included: No
    • Port Quantity: 2
    • Primary Port Size: M12 X 1.0
    • Product Condition: New
    • Reservoir Included: Yes
    • Reservoir Material: Plastic
    • Secondary Port Size: M12 X 1.0
  • Building on decades of experience using reverse engineering to remanufacture brake products, CARDONE engineers have meticulously designed our CARDONE® New Master Cylinders to match O.E. performance. Supplied with new O.E.-quality seals and cups, each unit is endurance-tested to ensure perfect fit, function and reliable performance.
Brand: Cardone
Additional Fitment Information:
Vehicle BrakeABS
2004 - Mercury Sable 4-Wheel ABS
Cardone
2004 Mercury Sable Brake Master Cylinder Cardone - Brake Master Cylinder

P311-51C4557    13-3048  New

4F1Z2140AA

Qty:
63.20
Cardone Brake Master Cylinder
  • without Traction Control Reservoir Included
  • Brake Master Cylinder
  • Product Attributes:
    • Bore Diameter (N): 1.000"
    • E-Waste: No
    • FAQs:
      • As A Rule, Always Use The Brake Fluid Recommended By The O.e. Which Is Stamped On The Master Cylinder Lid. Note: Always Use New Fluid From A Sealed Container.
      • Check Booster For A Defective Push Rod Seal. If This Seal Is Bad, It Could Drain The Brake Fluid Out Of The Master Cylinder.
      • Check The Steering And Suspension. Inspect Both Calipers For Binding Or Sticky Slides Or Pins. Check Brake Lining For Oil/grease Or Uneven Wear. Inspect Brake Hoses For Restriction. Check For Proper Tire Pressure.
      • Does A Step Bore Style Master Cylinder Require A Specific Bleeding Process?
      • Dot 3 And 4 Are Glycol-based Fluids And Dot 5 Is A Silicone-based Fluid.
      • First, Check For Air In The System. Make Sure Master Cylinder Is Level When Bleeding. Air Will Compress In A Hydraulic System Causing A Low Pedal. Then, Check For Brake Hose Swelling Or Expanding Under Pressure. Next, Check Brake Drums/discs For Proper Sp
      • How Can I Test A Master Cylinder To See If It's Bypassing?
      • I Replaced The Master Cylinder And Now The Pedal Is High And Hard. Why?
      • Most Likely, The Fluid In The System Is Contaminated. The Most Common Form Of Contamination Occurs When Petroleum-based Fluid Has Been Accidentally Introduced Into The Brake System. If That Has Happened It Is Almost Certain That All Rubber Components In T
      • My Original Master Cylinder Leaked Out Of The Back Of The Piston Into The Booster Area. Why?
      • One Side Of My Front Brakes Won’t Release, Why?
      • Replace All Brake Fluid. Brake Fluid Is Hygroscopic Which Means It Absorbs Moisture. Too Much Water In Brake Fluid Will Cause Vapor Lock And Apply Pressure To The Wheels. Also Check For Proper Push Rod Adjustments And Stop Light/cruise Control Switch Adju
      • Simply Plug The Master Cylinder Ports And Press The Brake Pedal. If The Master Cylinder Is Bypassing, The Pedal Will Go Down. If The Pedal Stops Hard, The Master Cylinder Is Ok.
      • The Brake Pedal Is Low And Spongy. Is It A Bad Master Cylinder?
      • The First Step To Bench Bleeding A Step Bore Is To Slowly Depress The Master Cylinder Piston, Then Release Slowly And Wait 20 Seconds Before Depressing Again. Never Pump Piston/pedal With A Step Bore Style Master Cylinder. Follow The Same Process On The V
      • The Master Cylinder Is Working Correctly. Check For A Faulty Brake Booster Or Frozen Wheel Cylinder/caliper.
      • This Is Caused By A Problem With The Caliper Or A Brake Hose.
      • What Causes The Brakes To Lock Up After Only A Couple Of Miles?
      • What Causes The Car To Pull To One Side During Braking?
      • What Type Of Fluid Should I Use: Dot 3, Dot 4 Or Dot 5?
      • What’s The Difference Between Dot 3, 4 And 5?
      • Why Is The Piston Stuck Inside The Bore Of My Master Cylinder?
    • Features and Benefits:
      • Bores Meet Critical Micro-finish Specifications To Eliminate Pitting And Corrosion, A Cause Of Premature Failure
      • Castings Feature A Premium Protective Coating To Minimize Corrosion And Extend Unit Life
      • Mounting Hardware And Bleeding Kits Are Supplied With Every Unit To Make The Installation And Bleeding Process Faster And Easier (where Applicable)
      • Only O.e.-quality Seals And Cups Are Used To Ensure O.e. Performance And Reliability. All Rubber Components Meet S.a.e. Specifications
      • Plastic Reservoirs Are Vacuum-tested To Ensure They Are Leak Free
      • Seals Are Temperature-cycled From -30°f To +220°f To Ensure Reliable Performance During Your Daily Commute
    • First Application Year: 2004
    • Installation Hardware Included: No
    • Master Cylinder Color/Finish: Gray
    • Master Cylinder Material: Aluminum
    • Mounting Hole Quantity: 2
    • Pedal Rod Included: No
    • Port Quantity: 2
    • Primary Port Size: M10 X 1.0
    • Product Condition: New
    • Reservoir Included: Yes
    • Reservoir Material: Plastic
    • Secondary Port Size: M12 X 1.0
  • Building on decades of experience using reverse engineering to remanufacture brake products, CARDONE engineers have meticulously designed our CARDONE® New Master Cylinders to match O.E. performance. Supplied with new O.E.-quality seals and cups, each unit is endurance-tested to ensure perfect fit, function and reliable performance.
Brand: Cardone
Additional Fitment Information:
Vehicle BrakeABS
2004 - Mercury Sable 4-Wheel ABS
Centric
2004 Mercury Sable Brake Master Cylinder Centric - Premium Master Cylinder-Preferred

P311-17B4517    130.61091  New

Qty:
44.94
Centric Brake Master Cylinder
  • Centric Premium Brake Master Cylinder
  • ; 2/04 - 2004 Except T/C
  • Match O.E. parts in quality; configuration and fitment. Complete with reservoirs; switches and floats. Original aluminum casting body design where applicable. Manufactured under the highest quality standards by OEM and OES manufacturers
  • Premium Master Cylinder-Preferred
  • Product Attributes:
    • Attribute ID (Type): California Proposition 65
    • Cylinder Bore Dia in: 1.0000
    • Cylinder Bore Dia mm: 25.40
    • Port Quantity: 2
    • Push Rod Lgth / Depth: 0.675
  • The Centric Parts brake hydraulic program is the most complete and up-to-date in the industry and includes Brake Master and Wheel Cylinders; Brake Hoses; Caliper And Wheel Cylinder Repair Kits And Remanufactured Power Boosters. Centric Parts Brake Master Cylinders match original equipment parts in quality; configuration and fitment. Cylinders are complete with reservoirs; switches; and floats and are offered with the original aluminum casting body design where applicable.
Brand: Centric
Additional Fitment Information:
Vehicle
2004 - Mercury Sable
Centric
2004 Mercury Sable Brake Master Cylinder Centric - Premium Master Cylinder-Preferred

P311-03A13B4    130.61156  New

Qty:
62.84
Centric Brake Master Cylinder
  • Centric Premium Brake Master Cylinder
  • ; 8/03 - 1/04 Angled Reservoir Except T/C
  • Match O.E. parts in quality; configuration and fitment. Complete with reservoirs; switches and floats. Original aluminum casting body design where applicable. Manufactured under the highest quality standards by OEM and OES manufacturers
  • Premium Master Cylinder-Preferred
  • Product Attributes:
    • Attribute ID (Type): California Proposition 65
    • Cylinder Bore Dia in: 1.0000
    • Cylinder Bore Dia mm: 25.40
    • Port Quantity: 2
    • Push Rod Lgth / Depth: 0.675
  • The Centric Parts brake hydraulic program is the most complete and up-to-date in the industry and includes Brake Master and Wheel Cylinders; Brake Hoses; Caliper And Wheel Cylinder Repair Kits And Remanufactured Power Boosters. Centric Parts Brake Master Cylinders match original equipment parts in quality; configuration and fitment. Cylinders are complete with reservoirs; switches; and floats and are offered with the original aluminum casting body design where applicable.
Brand: Centric
Additional Fitment Information:
Vehicle
2004 - Mercury Sable
Centric
2004 Mercury Sable Brake Master Cylinder Centric - Premium Master Cylinder-Preferred

P311-17B4517    130.61091  New

Qty:
44.94
Centric Brake Master Cylinder
  • Centric Premium Brake Master Cylinder
  • ; 8/03 - 1/04 Except T/C Oval Reservoir
  • Match O.E. parts in quality; configuration and fitment. Complete with reservoirs; switches and floats. Original aluminum casting body design where applicable. Manufactured under the highest quality standards by OEM and OES manufacturers
  • Premium Master Cylinder-Preferred
  • Product Attributes:
    • Attribute ID (Type): California Proposition 65
    • Cylinder Bore Dia in: 1.0000
    • Cylinder Bore Dia mm: 25.40
    • Port Quantity: 2
    • Push Rod Lgth / Depth: 0.675
  • The Centric Parts brake hydraulic program is the most complete and up-to-date in the industry and includes Brake Master and Wheel Cylinders; Brake Hoses; Caliper And Wheel Cylinder Repair Kits And Remanufactured Power Boosters. Centric Parts Brake Master Cylinders match original equipment parts in quality; configuration and fitment. Cylinders are complete with reservoirs; switches; and floats and are offered with the original aluminum casting body design where applicable.
Brand: Centric
Additional Fitment Information:
Vehicle
2004 - Mercury Sable
Centric
2004 Mercury Sable Brake Master Cylinder Centric - Premium Master Cylinder-Preferred

P311-16163B5    130.61119  New

Qty:
71.63
Centric Brake Master Cylinder
  • Centric Premium Brake Master Cylinder
  • ; T/C
  • Match O.E. parts in quality; configuration and fitment. Complete with reservoirs; switches and floats. Original aluminum casting body design where applicable. Manufactured under the highest quality standards by OEM and OES manufacturers
  • Premium Master Cylinder-Preferred
  • Product Attributes:
    • Attribute ID (Type): California Proposition 65
    • Cylinder Bore Dia in: 1.0000
    • Cylinder Bore Dia mm: 25.40
    • Port Quantity: 2
    • Push Rod Lgth / Depth: 0.672
  • The Centric Parts brake hydraulic program is the most complete and up-to-date in the industry and includes Brake Master and Wheel Cylinders; Brake Hoses; Caliper And Wheel Cylinder Repair Kits And Remanufactured Power Boosters. Centric Parts Brake Master Cylinders match original equipment parts in quality; configuration and fitment. Cylinders are complete with reservoirs; switches; and floats and are offered with the original aluminum casting body design where applicable.
Brand: Centric
Additional Fitment Information:
Vehicle
2004 - Mercury Sable
ACDelco
2004 Mercury Sable Brake Master Cylinder ACDelco

P311-3CD23E8    18M1427  New

Qty:
54.51
ACDelco Brake Master Cylinder
  • Professional; From 1/7/04; Without Traction Control
Brand: ACDelco
Additional Fitment Information:
Vehicle
2004 - Mercury Sable
Motorcraft
2004 Mercury Sable Brake Master Cylinder Motorcraft - Without Traction Assist

P311-0ACA449    BRMC18  New

Qty:
236.17
Motorcraft Brake Master Cylinder
  • Without Traction Assist
Brand: Motorcraft
Additional Fitment Information:
Vehicle
2004 - Mercury Sable

Showing 1 - 10 of 22 Products for Brake Master Cylinder.