802.589.0911 Live Chat With Us

Finish Selecting Your Vehicle

Choose your Engine for your 2001 Hyundai Santa Fe

  • 4 Cyl 2.4L
  • 6 Cyl 2.7L

Shop By Brand

The Following brands are available based on your search.

  • Cardone
    Cardone
  • Surtrak Axle
    Surtrak Axle

Showing Products For 2001 Hyundai Santa Fe CV Axle Shaft

Below are all the different brands and applications for 2001 Hyundai Santa Fe CV Axle Shaft

Showing 1 - 10 of 36 Products for CV Axle Shaft.

Refine Your Search

Cardone
2001 Hyundai Santa Fe CV Axle Shaft - Front Right 4 Cyl 2.4L Cardone - New Constant Velocity Drive Axle

P311-3717998    66-3358  New

4950026680 , 4950026681 , 4950026670 , 4950026671

Qty:
$64.58
Cardone CV Axle Shaft  Front Right
  • New Constant Velocity Drive Axle
  • Product Attributes:
    • ABS Ring Tooth Count: 52
    • Axle Nut Locking Type: Castle
    • Compressed Length: 38 1/4"
    • FAQs:
      • Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly.
      • Can I Let The Cv Drive Axles Hang While I Am Working On The Car?
      • I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?
      • I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?
      • I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?
      • Is It Ok To Use An Impact Hammer To Install The Retaining Nut?
      • Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint.
      • Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications.
      • No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One.
      • The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?
      • The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load.  This Is Typically An Outboard Joint Problem.
      • The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced.
      • The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up.
      • The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint.
      • The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut.  Should I Reuse It?
      • The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time.
      • The Wheels Wobble When I Make A Turn. What's The Problem?
      • When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?
      • When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?
      • When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?
      • When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking.
      • When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On.
    • Features and Benefits:
      • A New Axle Retaining Nut Is Supplied With Every Unit For A Hassle-free Installation, Due To The Likelihood That The Original Retaining Nut Is Worn Or Stripped
      • Boot Clamps Are Pneumatically Crimped, Creating A Perfect Seal Between The Boot And Housing
      • Cv Drive Axle Measurements Are Validated After Assembly To Ensure A Proper Fit
      • High-quality Grease Withstands High-temperature And High-torque Demands To Ensure Long-lasting, Reliable Performance
      • Neoprene Boots Are Designed With Additional Bellows, When Needed, To Resist Bellow Stress And Cracking, Which Is The Leading Cause Of Boot Failure
      • Proprietary Engineering Processes Ensure That All Cv Drive Axles Meet O.e. Form, Fit And Function
      • Severe-duty Cv Drive Axles Include A Thermoplastic Outboard Boot For Increased Life And Durability Versus A Traditional Neoprene Boot
      • Splines Are Precision Rolled To Ensure Proper Fit Of Cv Drive Axle Into The Mating Hub And Transmission, Which Eliminates Installation Hassles
      • Threads Are Precision Rolled To Ensure Proper Fit When Axle Nut Is Installed
      • Transmission Seal Diameter Is Precision-machined After Heat Treatment To Ensure Correct Surface Finish, Promoting Long Seal Life
    • Input Shaft Connection Style: Spline
    • Output Shaft Connection Style: Spline
    • Product Condition: New
    • Spindle Nut Hex Head Size: 32mm
    • Spindle Nut Thread Size: M22 X 1.5
  • CARDONE's extensive experience in testing and engineering CV Drive Axles is the foundation behind our proprietary method of engineering a product that meets and even exceed O.E. performance. We have researched the reasons why original CVs typically fail and designed new solutions to avoid repeat failure. For example, our Neoprene boots are designed with additional bellows, when needed, to resist bellow stress and ozone cracking - the leading cause of boot failure. Additionally, all CV Drive Axle shafts are individually verified for straightness, resulting in vibration-free performance at all speeds.
Brand: Cardone
Position: Front Right
Additional Fitment Information:
Vehicle Transmission Drive Type Position Block Engine CID CC
2001 - Hyundai Santa Fe Automatic FWD Front Right L 4 Cyl 2.4L - 2351
Cardone
2001 Hyundai Santa Fe CV Axle Shaft - Front Left 6 Cyl 2.7L Cardone - New Constant Velocity Drive Axle

P311-311310A    66-3360  New

4950026501 , 4950026510 , 4950126501 , 4950026500 , 4950026511

Qty:
$66.70
Cardone CV Axle Shaft  Front Left
  • New Constant Velocity Drive Axle
  • Product Attributes:
    • ABS Ring Tooth Count: 52
    • Axle Nut Locking Type: Castle
    • Compressed Length: 25 5/8"
    • FAQs:
      • Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly.
      • Can I Let The Cv Drive Axles Hang While I Am Working On The Car?
      • I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?
      • I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?
      • I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?
      • Is It Ok To Use An Impact Hammer To Install The Retaining Nut?
      • Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint.
      • Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications.
      • No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One.
      • The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?
      • The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load.  This Is Typically An Outboard Joint Problem.
      • The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced.
      • The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up.
      • The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint.
      • The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut.  Should I Reuse It?
      • The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time.
      • The Wheels Wobble When I Make A Turn. What's The Problem?
      • When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?
      • When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?
      • When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?
      • When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking.
      • When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On.
    • Features and Benefits:
      • A New Axle Retaining Nut Is Supplied With Every Unit For A Hassle-free Installation, Due To The Likelihood That The Original Retaining Nut Is Worn Or Stripped
      • Boot Clamps Are Pneumatically Crimped, Creating A Perfect Seal Between The Boot And Housing
      • Cv Drive Axle Measurements Are Validated After Assembly To Ensure A Proper Fit
      • High-quality Grease Withstands High-temperature And High-torque Demands To Ensure Long-lasting, Reliable Performance
      • Neoprene Boots Are Designed With Additional Bellows, When Needed, To Resist Bellow Stress And Cracking, Which Is The Leading Cause Of Boot Failure
      • Proprietary Engineering Processes Ensure That All Cv Drive Axles Meet O.e. Form, Fit And Function
      • Severe-duty Cv Drive Axles Include A Thermoplastic Outboard Boot For Increased Life And Durability Versus A Traditional Neoprene Boot
      • Splines Are Precision Rolled To Ensure Proper Fit Of Cv Drive Axle Into The Mating Hub And Transmission, Which Eliminates Installation Hassles
      • Threads Are Precision Rolled To Ensure Proper Fit When Axle Nut Is Installed
      • Transmission Seal Diameter Is Precision-machined After Heat Treatment To Ensure Correct Surface Finish, Promoting Long Seal Life
    • Input Shaft Connection Style: Spline
    • Output Shaft Connection Style: Spline
    • Product Condition: New
    • Spindle Nut Hex Head Size: 32mm
    • Spindle Nut Thread Size: M22 X 1.5
  • CARDONE's extensive experience in testing and engineering CV Drive Axles is the foundation behind our proprietary method of engineering a product that meets and even exceed O.E. performance. We have researched the reasons why original CVs typically fail and designed new solutions to avoid repeat failure. For example, our Neoprene boots are designed with additional bellows, when needed, to resist bellow stress and ozone cracking - the leading cause of boot failure. Additionally, all CV Drive Axle shafts are individually verified for straightness, resulting in vibration-free performance at all speeds.
Brand: Cardone
Position: Front Left
Additional Fitment Information:
Vehicle Transmission Drive Type Position Block Engine CID CC
2001 - Hyundai Santa Fe Automatic FWD Front Left V 6 Cyl 2.7L - 2656
Cardone
2001 Hyundai Santa Fe CV Axle Shaft - Front Left 4 Cyl 2.4L Cardone - New Constant Velocity Drive Axle

P311-12BA04E    66-3356  New

4950026621 , 4950026631 , 4950026630 , 4950026620

Qty:
$63.40
Cardone CV Axle Shaft  Front Left
  • New Constant Velocity Drive Axle
  • Product Attributes:
    • ABS Ring Tooth Count: 52
    • Axle Nut Locking Type: Castle
    • Compressed Length: 25 1/2"
    • FAQs:
      • Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly.
      • Can I Let The Cv Drive Axles Hang While I Am Working On The Car?
      • I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?
      • I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?
      • I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?
      • Is It Ok To Use An Impact Hammer To Install The Retaining Nut?
      • Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint.
      • Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications.
      • No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One.
      • The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?
      • The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load.  This Is Typically An Outboard Joint Problem.
      • The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced.
      • The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up.
      • The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint.
      • The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut.  Should I Reuse It?
      • The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time.
      • The Wheels Wobble When I Make A Turn. What's The Problem?
      • When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?
      • When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?
      • When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?
      • When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking.
      • When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On.
    • Features and Benefits:
      • A New Axle Retaining Nut Is Supplied With Every Unit For A Hassle-free Installation, Due To The Likelihood That The Original Retaining Nut Is Worn Or Stripped
      • Boot Clamps Are Pneumatically Crimped, Creating A Perfect Seal Between The Boot And Housing
      • Cv Drive Axle Measurements Are Validated After Assembly To Ensure A Proper Fit
      • High-quality Grease Withstands High-temperature And High-torque Demands To Ensure Long-lasting, Reliable Performance
      • Neoprene Boots Are Designed With Additional Bellows, When Needed, To Resist Bellow Stress And Cracking, Which Is The Leading Cause Of Boot Failure
      • Proprietary Engineering Processes Ensure That All Cv Drive Axles Meet O.e. Form, Fit And Function
      • Severe-duty Cv Drive Axles Include A Thermoplastic Outboard Boot For Increased Life And Durability Versus A Traditional Neoprene Boot
      • Splines Are Precision Rolled To Ensure Proper Fit Of Cv Drive Axle Into The Mating Hub And Transmission, Which Eliminates Installation Hassles
      • Threads Are Precision Rolled To Ensure Proper Fit When Axle Nut Is Installed
      • Transmission Seal Diameter Is Precision-machined After Heat Treatment To Ensure Correct Surface Finish, Promoting Long Seal Life
    • Input Shaft Connection Style: Spline
    • Output Shaft Connection Style: Spline
    • Product Condition: New
    • Spindle Nut Hex Head Size: 32mm
    • Spindle Nut Thread Size: M22 X 1.5
  • CARDONE's extensive experience in testing and engineering CV Drive Axles is the foundation behind our proprietary method of engineering a product that meets and even exceed O.E. performance. We have researched the reasons why original CVs typically fail and designed new solutions to avoid repeat failure. For example, our Neoprene boots are designed with additional bellows, when needed, to resist bellow stress and ozone cracking - the leading cause of boot failure. Additionally, all CV Drive Axle shafts are individually verified for straightness, resulting in vibration-free performance at all speeds.
Brand: Cardone
Position: Front Left
Additional Fitment Information:
Vehicle Transmission Drive Type Position Block Engine CID CC
2001 - Hyundai Santa Fe Automatic FWD Front Left L 4 Cyl 2.4L - 2351
Cardone
2001 Hyundai Santa Fe CV Axle Shaft - Front Right 6 Cyl 2.7L Cardone - New Constant Velocity Drive Axle

P311-3427C80    66-3370  New

4950126860 , 4950126560 , 4950126561

Qty:
$69.95
Cardone CV Axle Shaft  Front Right
  • New Constant Velocity Drive Axle
  • Product Attributes:
    • ABS Ring Tooth Count: 52
    • Axle Nut Locking Type: Castle
    • Compressed Length: 22 5/8"
    • FAQs:
      • Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly.
      • Can I Let The Cv Drive Axles Hang While I Am Working On The Car?
      • I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?
      • I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?
      • I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?
      • Is It Ok To Use An Impact Hammer To Install The Retaining Nut?
      • Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint.
      • Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications.
      • No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One.
      • The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?
      • The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load.  This Is Typically An Outboard Joint Problem.
      • The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced.
      • The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up.
      • The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint.
      • The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut.  Should I Reuse It?
      • The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time.
      • The Wheels Wobble When I Make A Turn. What's The Problem?
      • When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?
      • When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?
      • When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?
      • When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking.
      • When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On.
    • Features and Benefits:
      • A New Axle Retaining Nut Is Supplied With Every Unit For A Hassle-free Installation, Due To The Likelihood That The Original Retaining Nut Is Worn Or Stripped
      • Boot Clamps Are Pneumatically Crimped, Creating A Perfect Seal Between The Boot And Housing
      • Cv Drive Axle Measurements Are Validated After Assembly To Ensure A Proper Fit
      • High-quality Grease Withstands High-temperature And High-torque Demands To Ensure Long-lasting, Reliable Performance
      • Neoprene Boots Are Designed With Additional Bellows, When Needed, To Resist Bellow Stress And Cracking, Which Is The Leading Cause Of Boot Failure
      • Proprietary Engineering Processes Ensure That All Cv Drive Axles Meet O.e. Form, Fit And Function
      • Severe-duty Cv Drive Axles Include A Thermoplastic Outboard Boot For Increased Life And Durability Versus A Traditional Neoprene Boot
      • Splines Are Precision Rolled To Ensure Proper Fit Of Cv Drive Axle Into The Mating Hub And Transmission, Which Eliminates Installation Hassles
      • Threads Are Precision Rolled To Ensure Proper Fit When Axle Nut Is Installed
      • Transmission Seal Diameter Is Precision-machined After Heat Treatment To Ensure Correct Surface Finish, Promoting Long Seal Life
    • Input Shaft Connection Style: Spline
    • Output Shaft Connection Style: Spline
    • Product Condition: New
    • Spindle Nut Hex Head Size: 32mm
    • Spindle Nut Thread Size: M22 X 1.5
  • CARDONE's extensive experience in testing and engineering CV Drive Axles is the foundation behind our proprietary method of engineering a product that meets and even exceed O.E. performance. We have researched the reasons why original CVs typically fail and designed new solutions to avoid repeat failure. For example, our Neoprene boots are designed with additional bellows, when needed, to resist bellow stress and ozone cracking - the leading cause of boot failure. Additionally, all CV Drive Axle shafts are individually verified for straightness, resulting in vibration-free performance at all speeds.
Brand: Cardone
Position: Front Right
Additional Fitment Information:
Vehicle Transmission Drive Type Position Block Engine CID CC
2001 - Hyundai Santa Fe Automatic 4WD Front Right V 6 Cyl 2.7L - 2656
Cardone
2001 Hyundai Santa Fe CV Axle Shaft - Front Left 6 Cyl 2.7L Cardone - New Constant Velocity Drive Axle

P311-4D8C0D6    66-3368  New

4950126511 , 4950126501 , 4950126510 , 4950126500

Qty:
$61.61
Cardone CV Axle Shaft  Front Left
  • New Constant Velocity Drive Axle
  • Product Attributes:
    • ABS Ring Tooth Count: 52
    • Axle Nut Locking Type: Castle
    • Compressed Length: 22 11/16"
    • FAQs:
      • Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly.
      • Can I Let The Cv Drive Axles Hang While I Am Working On The Car?
      • I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?
      • I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?
      • I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?
      • Is It Ok To Use An Impact Hammer To Install The Retaining Nut?
      • Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint.
      • Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications.
      • No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One.
      • The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?
      • The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load.  This Is Typically An Outboard Joint Problem.
      • The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced.
      • The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up.
      • The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint.
      • The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut.  Should I Reuse It?
      • The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time.
      • The Wheels Wobble When I Make A Turn. What's The Problem?
      • When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?
      • When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?
      • When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?
      • When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking.
      • When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On.
    • Features and Benefits:
      • A New Axle Retaining Nut Is Supplied With Every Unit For A Hassle-free Installation, Due To The Likelihood That The Original Retaining Nut Is Worn Or Stripped
      • Boot Clamps Are Pneumatically Crimped, Creating A Perfect Seal Between The Boot And Housing
      • Cv Drive Axle Measurements Are Validated After Assembly To Ensure A Proper Fit
      • High-quality Grease Withstands High-temperature And High-torque Demands To Ensure Long-lasting, Reliable Performance
      • Neoprene Boots Are Designed With Additional Bellows, When Needed, To Resist Bellow Stress And Cracking, Which Is The Leading Cause Of Boot Failure
      • Proprietary Engineering Processes Ensure That All Cv Drive Axles Meet O.e. Form, Fit And Function
      • Severe-duty Cv Drive Axles Include A Thermoplastic Outboard Boot For Increased Life And Durability Versus A Traditional Neoprene Boot
      • Splines Are Precision Rolled To Ensure Proper Fit Of Cv Drive Axle Into The Mating Hub And Transmission, Which Eliminates Installation Hassles
      • Threads Are Precision Rolled To Ensure Proper Fit When Axle Nut Is Installed
      • Transmission Seal Diameter Is Precision-machined After Heat Treatment To Ensure Correct Surface Finish, Promoting Long Seal Life
    • Input Shaft Connection Style: Spline
    • Output Shaft Connection Style: Spline
    • Product Condition: New
    • Spindle Nut Hex Head Size: 32mm
    • Spindle Nut Thread Size: M22 X 1.5
  • CARDONE's extensive experience in testing and engineering CV Drive Axles is the foundation behind our proprietary method of engineering a product that meets and even exceed O.E. performance. We have researched the reasons why original CVs typically fail and designed new solutions to avoid repeat failure. For example, our Neoprene boots are designed with additional bellows, when needed, to resist bellow stress and ozone cracking - the leading cause of boot failure. Additionally, all CV Drive Axle shafts are individually verified for straightness, resulting in vibration-free performance at all speeds.
Brand: Cardone
Position: Front Left
Additional Fitment Information:
Vehicle Transmission Drive Type Position Block Engine CID CC
2001 - Hyundai Santa Fe Automatic 4WD Front Left V 6 Cyl 2.7L - 2656
Cardone
2001 Hyundai Santa Fe CV Axle Shaft - Front Right 4 Cyl 2.4L Cardone - Reman. Constant Velocity Drive Axle

P311-5D6157B    60-3357  Remanufactured

4950038450 , 4950038452 , 4950038451 , 4950026671 , 495003C451 , 4950838E00 , 4950026670 , 4950838G00 , 495003C452

Qty:
$60.22
Cardone CV Axle Shaft  Front Right
  • Remanufactured Constant Velocity Drive Axle
  • Reman. Constant Velocity Drive Axle
  • Product Attributes:
    • Compressed Length: 38 3/16"
    • FAQs:
      • Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly.
      • Are The Cv Drive Axle Shafts Balanced At The Factory?
      • Can I Let The Cv Drive Axles Hang While I Am Working On The Car?
      • I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?
      • I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?
      • I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?
      • Is It Ok To Use An Impact Hammer To Install The Retaining Nut?
      • Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint.
      • Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications.
      • No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One.
      • Shafts Are Inspected 100% For Run Out To Prevent Vibrations.  Only Shafts That Meet The Specifications For Run Out Are Utilized In The Remanufacturing Of A Cv Drive Axle Assembly.
      • The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?
      • The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load.  This Is Typically An Outboard Joint Problem.
      • The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced.
      • The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up.
      • The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint.
      • The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut.  Should I Reuse It?
      • The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time.
      • The Wheels Wobble When I Make A Turn. What's The Problem?
      • When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?
      • When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?
      • When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?
      • When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking.
      • When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On.
    • Features and Benefits:
      • Boot Clamps Are Pneumatically Crimped, Creating A Perfect Seal Between The Boot And Housing.
      • Cv Drive Axle Is Measured After Assembly To Ensure Proper Fit.
      • Cv Drive Axle Shafts Are Inspected For Run Out To Prevent Vibration.
      • High-quality Grease Withstands High-temperature And Pressure Extremes, Which Extends Joint Life.
      • High-tech Grinding Machines Maintain The Original Design Of The Outer Housing, Race And Cage To Guarantee Reliable Performance.
      • Neoprene Boots Ensure Excellent Environmental Stress Resistance, Which Eliminates Cracking - A Leading Cause Of Boot Failure.
      • Splines Are Chased To Ensure Proper Fit Of The Axle Into The Mating Hub And Transmission, Which Eliminates Installation Hassles.
      • Threads Are Chased To Ensure Proper Fit Of The New Retaining Nut Supplied With Each Cv Drive Axle.
    • Input Shaft Connection Style: Spline
    • Output Shaft Connection Style: Spline
    • Product Condition: Remanufactured
  • CARDONE's extensive experience in testing and engineering CV Drive Axles is the foundation behind our proprietary method of engineering a product that meets and even exceed O.E. performance. We have researched the reasons why original CVs typically fail and designed new solutions to avoid repeat failure. For example, our Neoprene boots are designed with additional bellows, when needed, to resist bellow stress and ozone cracking - the leading cause of boot failure. Additionally, all CV Drive Axle shafts are individually verified for straightness, resulting in vibration-free performance at all speeds.
Brand: Cardone
Position: Front Right
Additional Fitment Information:
Vehicle Transmission BrakeABS Drive Type Position Block Engine CID CC
2001 - Hyundai Santa Fe Automatic Non-ABS FWD Front Right L 4 Cyl 2.4L - 2351
Cardone
2001 Hyundai Santa Fe CV Axle Shaft - Front Left 6 Cyl 2.7L Cardone - Reman. Constant Velocity Drive Axle

P311-3D467CE    60-3360  Remanufactured

4950026511 , 4950026510

Qty:
$45.00 $65.42
Cardone CV Axle Shaft  Front Left
  • Remanufactured Constant Velocity Drive Axle
  • Reman. Constant Velocity Drive Axle
  • Product Attributes:
    • ABS Ring Tooth Count: 52
    • Compressed Length: 25 5/8"
    • FAQs:
      • Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly.
      • Are The Cv Drive Axle Shafts Balanced At The Factory?
      • Can I Let The Cv Drive Axles Hang While I Am Working On The Car?
      • I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?
      • I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?
      • I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?
      • Is It Ok To Use An Impact Hammer To Install The Retaining Nut?
      • Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint.
      • Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications.
      • No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One.
      • Shafts Are Inspected 100% For Run Out To Prevent Vibrations.  Only Shafts That Meet The Specifications For Run Out Are Utilized In The Remanufacturing Of A Cv Drive Axle Assembly.
      • The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?
      • The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load.  This Is Typically An Outboard Joint Problem.
      • The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced.
      • The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up.
      • The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint.
      • The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut.  Should I Reuse It?
      • The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time.
      • The Wheels Wobble When I Make A Turn. What's The Problem?
      • When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?
      • When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?
      • When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?
      • When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking.
      • When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On.
    • Features and Benefits:
      • Boot Clamps Are Pneumatically Crimped, Creating A Perfect Seal Between The Boot And Housing.
      • Cv Drive Axle Is Measured After Assembly To Ensure Proper Fit.
      • Cv Drive Axle Shafts Are Inspected For Run Out To Prevent Vibration.
      • High-quality Grease Withstands High-temperature And Pressure Extremes, Which Extends Joint Life.
      • High-tech Grinding Machines Maintain The Original Design Of The Outer Housing, Race And Cage To Guarantee Reliable Performance.
      • Neoprene Boots Ensure Excellent Environmental Stress Resistance, Which Eliminates Cracking - A Leading Cause Of Boot Failure.
      • Splines Are Chased To Ensure Proper Fit Of The Axle Into The Mating Hub And Transmission, Which Eliminates Installation Hassles.
      • Threads Are Chased To Ensure Proper Fit Of The New Retaining Nut Supplied With Each Cv Drive Axle.
    • Input Shaft Connection Style: Spline
    • Output Shaft Connection Style: Spline
    • Product Condition: Remanufactured
  • CARDONE's extensive experience in testing and engineering CV Drive Axles is the foundation behind our proprietary method of engineering a product that meets and even exceed O.E. performance. We have researched the reasons why original CVs typically fail and designed new solutions to avoid repeat failure. For example, our Neoprene boots are designed with additional bellows, when needed, to resist bellow stress and ozone cracking - the leading cause of boot failure. Additionally, all CV Drive Axle shafts are individually verified for straightness, resulting in vibration-free performance at all speeds.
Brand: Cardone
Position: Front Left
Additional Fitment Information:
Vehicle Transmission BrakeABS Trans. Speed Drive Type Position Block Engine CID CC
2001 - Hyundai Santa Fe Automatic 4-Wheel ABS 4 FWD Front Left V 6 Cyl 2.7L - 2656
Cardone
2001 Hyundai Santa Fe CV Axle Shaft - Front Right 6 Cyl 2.7L Cardone - Reman. Constant Velocity Drive Axle

P311-0F65A6F    60-3362  Remanufactured

4950026461 , 4950026460

Qty:
$40.50 $65.42
Cardone CV Axle Shaft  Front Right
  • Remanufactured Constant Velocity Drive Axle
  • Reman. Constant Velocity Drive Axle
  • Product Attributes:
    • ABS Ring Tooth Count: 52
    • Compressed Length: 23 13/16"
    • FAQs:
      • Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly.
      • Are The Cv Drive Axle Shafts Balanced At The Factory?
      • Can I Let The Cv Drive Axles Hang While I Am Working On The Car?
      • I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?
      • I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?
      • I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?
      • Is It Ok To Use An Impact Hammer To Install The Retaining Nut?
      • Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint.
      • Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications.
      • No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One.
      • Shafts Are Inspected 100% For Run Out To Prevent Vibrations.  Only Shafts That Meet The Specifications For Run Out Are Utilized In The Remanufacturing Of A Cv Drive Axle Assembly.
      • The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?
      • The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load.  This Is Typically An Outboard Joint Problem.
      • The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced.
      • The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up.
      • The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint.
      • The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut.  Should I Reuse It?
      • The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time.
      • The Wheels Wobble When I Make A Turn. What's The Problem?
      • When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?
      • When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?
      • When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?
      • When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking.
      • When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On.
    • Features and Benefits:
      • Boot Clamps Are Pneumatically Crimped, Creating A Perfect Seal Between The Boot And Housing.
      • Cv Drive Axle Is Measured After Assembly To Ensure Proper Fit.
      • Cv Drive Axle Shafts Are Inspected For Run Out To Prevent Vibration.
      • High-quality Grease Withstands High-temperature And Pressure Extremes, Which Extends Joint Life.
      • High-tech Grinding Machines Maintain The Original Design Of The Outer Housing, Race And Cage To Guarantee Reliable Performance.
      • Neoprene Boots Ensure Excellent Environmental Stress Resistance, Which Eliminates Cracking - A Leading Cause Of Boot Failure.
      • Splines Are Chased To Ensure Proper Fit Of The Axle Into The Mating Hub And Transmission, Which Eliminates Installation Hassles.
      • Threads Are Chased To Ensure Proper Fit Of The New Retaining Nut Supplied With Each Cv Drive Axle.
    • Input Shaft Connection Style: Spline
    • Input Shaft Spline Count: 24 + 2 Blank
    • Output Shaft Connection Style: Spline
    • Product Condition: Remanufactured
  • CARDONE's extensive experience in testing and engineering CV Drive Axles is the foundation behind our proprietary method of engineering a product that meets and even exceed O.E. performance. We have researched the reasons why original CVs typically fail and designed new solutions to avoid repeat failure. For example, our Neoprene boots are designed with additional bellows, when needed, to resist bellow stress and ozone cracking - the leading cause of boot failure. Additionally, all CV Drive Axle shafts are individually verified for straightness, resulting in vibration-free performance at all speeds.
Brand: Cardone
Position: Front Right
Additional Fitment Information:
Vehicle Transmission BrakeABS Drive Type Position Block Engine CID CC
2001 - Hyundai Santa Fe Automatic 4-Wheel ABS FWD Front Right V 6 Cyl 2.7L - 2656
Cardone
2001 Hyundai Santa Fe CV Axle Shaft - Front Right 6 Cyl 2.7L Cardone - Reman. Constant Velocity Drive Axle

P311-2C9E53B    60-3370  Remanufactured

4950126560 , 4950126860 , 4950126561

Qty:
$34.20 $65.42
Cardone CV Axle Shaft  Front Right
  • Remanufactured Constant Velocity Drive Axle
  • Reman. Constant Velocity Drive Axle
  • Product Attributes:
    • ABS Ring Tooth Count: 52
    • Compressed Length: 24"
    • FAQs:
      • Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly.
      • Are The Cv Drive Axle Shafts Balanced At The Factory?
      • Can I Let The Cv Drive Axles Hang While I Am Working On The Car?
      • I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?
      • I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?
      • I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?
      • Is It Ok To Use An Impact Hammer To Install The Retaining Nut?
      • Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint.
      • Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications.
      • No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One.
      • Shafts Are Inspected 100% For Run Out To Prevent Vibrations.  Only Shafts That Meet The Specifications For Run Out Are Utilized In The Remanufacturing Of A Cv Drive Axle Assembly.
      • The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?
      • The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load.  This Is Typically An Outboard Joint Problem.
      • The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced.
      • The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up.
      • The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint.
      • The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut.  Should I Reuse It?
      • The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time.
      • The Wheels Wobble When I Make A Turn. What's The Problem?
      • When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?
      • When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?
      • When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?
      • When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking.
      • When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On.
    • Features and Benefits:
      • Boot Clamps Are Pneumatically Crimped, Creating A Perfect Seal Between The Boot And Housing.
      • Cv Drive Axle Is Measured After Assembly To Ensure Proper Fit.
      • Cv Drive Axle Shafts Are Inspected For Run Out To Prevent Vibration.
      • High-quality Grease Withstands High-temperature And Pressure Extremes, Which Extends Joint Life.
      • High-tech Grinding Machines Maintain The Original Design Of The Outer Housing, Race And Cage To Guarantee Reliable Performance.
      • Neoprene Boots Ensure Excellent Environmental Stress Resistance, Which Eliminates Cracking - A Leading Cause Of Boot Failure.
      • Splines Are Chased To Ensure Proper Fit Of The Axle Into The Mating Hub And Transmission, Which Eliminates Installation Hassles.
      • Threads Are Chased To Ensure Proper Fit Of The New Retaining Nut Supplied With Each Cv Drive Axle.
    • Input Shaft Connection Style: Spline
    • Input Shaft Spline Count: 24 + 2 Blank
    • Output Shaft Connection Style: Spline
    • Product Condition: Remanufactured
  • CARDONE's extensive experience in testing and engineering CV Drive Axles is the foundation behind our proprietary method of engineering a product that meets and even exceed O.E. performance. We have researched the reasons why original CVs typically fail and designed new solutions to avoid repeat failure. For example, our Neoprene boots are designed with additional bellows, when needed, to resist bellow stress and ozone cracking - the leading cause of boot failure. Additionally, all CV Drive Axle shafts are individually verified for straightness, resulting in vibration-free performance at all speeds.
Brand: Cardone
Position: Front Right
Additional Fitment Information:
Vehicle Transmission BrakeABS Drive Type Position Block Engine CID CC
2001 - Hyundai Santa Fe Automatic 4-Wheel ABS 4WD Front Right V 6 Cyl 2.7L - 2656
Cardone
2001 Hyundai Santa Fe CV Axle Shaft - Front Left 6 Cyl 2.7L Cardone - Reman. Constant Velocity Drive Axle

P311-5583D79    60-3368  Remanufactured

4950126511 , 4950126510

Qty:
$40.50 $65.42
Cardone CV Axle Shaft  Front Left
  • Remanufactured Constant Velocity Drive Axle
  • Reman. Constant Velocity Drive Axle
  • Product Attributes:
    • ABS Ring Tooth Count: 52
    • Compressed Length: 25 1/2"
    • FAQs:
      • Always Use The Proper Press Type Tool To Remove The Old Stub Shaft. Never Strike The Outer Joint Stub Shaft With A Hammer. It Will Damage The Unit And Possibly Do Damage To The Hub Bearing Assembly.
      • Are The Cv Drive Axle Shafts Balanced At The Factory?
      • Can I Let The Cv Drive Axles Hang While I Am Working On The Car?
      • I Hear A Grinding Noise From The Front End While Driving And See Grease On The Chassis And Suspension. What Is Causing This?
      • I Installed A Replacement Cv Drive Axle And Now My Abs Light Is On And Won't Go Out. Why?
      • I Removed Both Cv Drive Axles At The Same Time And Now I Am Having Problems Reinstalling Them. What Can I Do?
      • Is It Ok To Use An Impact Hammer To Install The Retaining Nut?
      • Never Allow The Cv Drive Axles To Hang Unsupported. This Can Lead To Axle Separation And Damage To The Inner Joint.
      • Never Use An Impact Wrench To Install The Retaining Nut On The Cv Drive Axle. Always Use A Torque Wrench And Torque The Nut To Manufacture's Specifications.
      • No! A Prevailing Torque Lock Nut Should Never Be Reused. Always Discard The Old Nut And Install A New One.
      • Shafts Are Inspected 100% For Run Out To Prevent Vibrations.  Only Shafts That Meet The Specifications For Run Out Are Utilized In The Remanufacturing Of A Cv Drive Axle Assembly.
      • The Cv Drive Axle Outboard Joint Stub Shaft Is Stuck In The Hub Assembly. What's The Best Way To Remove It?
      • The Most Likely Cause Is A Broken Bearing Cage Due To Excessive Torque Load.  This Is Typically An Outboard Joint Problem.
      • The Most Likely Cause Is A Defective Or Worn Outer Cv Drive Axle Joint. It May Be Time To Get It Replaced.
      • The Most Likely Cause Is The Drive Train Shifting In The Chassis Due To A Broken Engine Mount Or Hardware, Causing Misalignment Of The Cv Drive Axle And Causing The Inner Joint To Bind Or Hang Up.
      • The Most Likely Problem Is The Outer Cv Drive Axle Boot Has Ruptured, Causing The Grease To Leak Out, Allowing Contamination (water And Dirt) To Enter And Damage The Joint.
      • The Old Cv Drive Axle Has A Locking Style (prevailing Torque) Nut.  Should I Reuse It?
      • The Transaxle Gear Alignment Has Been Lost. On Some Vehicles It Will Be Necessary To Disassemble The Transaxle To Properly Align The Output Gears. Always Remove And Install One Cv Drive Axle At A Time.
      • The Wheels Wobble When I Make A Turn. What's The Problem?
      • When I Cut The Wheel Hard And Step On The Gas, I Hear Loud Clicking And Snapping. What's Making That Noise?
      • When I Replace The Cv Drive Axles, Should I Reuse The Old Seals?
      • When I Step On The Gas, I Hear A Loud Thump And Feel A Bad Vibration. What's Wrong?
      • When Replacing Cv Drive Axle Assemblies, Always Install New Transaxle Seals To Avoid Leaking.
      • When The Replacement Drive Axle Was Installed, The Sensor Ring, Sensor, Or Sensor Wiring On Or Near The Axle Was Damaged, Causing An Erratic Speed Signal To The Abs Module And Setting The Light On.
    • Features and Benefits:
      • Boot Clamps Are Pneumatically Crimped, Creating A Perfect Seal Between The Boot And Housing.
      • Cv Drive Axle Is Measured After Assembly To Ensure Proper Fit.
      • Cv Drive Axle Shafts Are Inspected For Run Out To Prevent Vibration.
      • High-quality Grease Withstands High-temperature And Pressure Extremes, Which Extends Joint Life.
      • High-tech Grinding Machines Maintain The Original Design Of The Outer Housing, Race And Cage To Guarantee Reliable Performance.
      • Neoprene Boots Ensure Excellent Environmental Stress Resistance, Which Eliminates Cracking - A Leading Cause Of Boot Failure.
      • Splines Are Chased To Ensure Proper Fit Of The Axle Into The Mating Hub And Transmission, Which Eliminates Installation Hassles.
      • Threads Are Chased To Ensure Proper Fit Of The New Retaining Nut Supplied With Each Cv Drive Axle.
    • Input Shaft Connection Style: Spline
    • Output Shaft Connection Style: Spline
    • Product Condition: Remanufactured
  • CARDONE's extensive experience in testing and engineering CV Drive Axles is the foundation behind our proprietary method of engineering a product that meets and even exceed O.E. performance. We have researched the reasons why original CVs typically fail and designed new solutions to avoid repeat failure. For example, our Neoprene boots are designed with additional bellows, when needed, to resist bellow stress and ozone cracking - the leading cause of boot failure. Additionally, all CV Drive Axle shafts are individually verified for straightness, resulting in vibration-free performance at all speeds.
Brand: Cardone
Position: Front Left
Additional Fitment Information:
Vehicle Transmission BrakeABS Drive Type Position Block Engine CID CC
2001 - Hyundai Santa Fe Automatic 4-Wheel ABS 4WD Front Left V 6 Cyl 2.7L - 2656

Showing 1 - 10 of 36 Products for CV Axle Shaft.