802.589.0911 Live Chat With Us

Finish Selecting Your Vehicle

Choose your Engine for your 2000 Chrysler Voyager

  • 4 Cyl 2.4L
  • 6 Cyl 3.0L
  • 6 Cyl 3.3L

Showing Products For 2000 Chrysler Voyager Engine Control Module

Below are all the different brands and applications for 2000 Chrysler Voyager Engine Control Module

Showing 1 - 6 of 6 Products for Engine Control Module.

Refine Your Search

Cardone
2000 Chrysler Voyager Engine Control Module 6 Cyl 3.3L Cardone - Reman. Engine Control Computer

P311-4C00BCD    79-5280V  Remanufactured

04727280AA , 04727280AB , 4727280AB , 4727280AA

Qty:
$35.10 $178.77
Cardone Engine Control Module
  • Remanufactured Engine Control Computer
  • Vehicle specific Flash programming required ON or OFF the vehicle.Accurate VIN and mileage are req'd
  • Reman. Engine Control Computer
  • Product Attributes:
    • Connector/Terminal Configuration: Pin/male; Pin/male
    • FAQs:
      • Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Injection Pulse On Fuel Pump, Intermittent Starting Problems.
      • Chrysler Models 1996 And Newer Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?
      • Do Gm Vehicles Have A Passive Anti-theft System?
      • Do I Have To Transfer Anything From My Original Ecm/pcm?
      • Do I Need A Scanner To Reset The Anti-theft System
      • Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn.
      • No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application.
      • Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays.
      • Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module.
      • The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • What Are The Most Common Symptoms Of A Bad Pcm?
      • What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?
      • What’s The Difference Between An Ecm And A Pcm?
      • Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System.
      • “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission.
    • Features and Benefits:
      • Meets O.e. Fit And Function.
      • Meets Or Exceeds O.e.m Performance
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated, Computerized Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
    • Product Condition: Remanufactured
    • Terminal Quantity: 40, 40
  • CARDONE® Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design weaknesses. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant, and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back to peak performance.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
2000 - Chrysler Voyager V 6 Cyl 3.3L 201 3301
Cardone
2000 Chrysler Voyager Engine Control Module 6 Cyl 3.0L Cardone - Reman. Engine Control Computer

P311-5431309    79-7276V  Remanufactured

04727276AC , 04727276AD , 4727276AA , 04727276AA , 04727276AB , 4727276AB , 4727276AC , 4727276AD

Qty:
$41.40 $163.80
Cardone Engine Control Module
  • Remanufactured Engine Control Computer
  • Vehicle specific Flash programming required ON or OFF the vehicle.Accurate VIN and mileage are req'd
  • Reman. Engine Control Computer
  • Product Attributes:
    • Connector/Terminal Configuration: Pin/male; Pin/male
    • FAQs:
      • Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Injection Pulse On Fuel Pump, Intermittent Starting Problems.
      • Chrysler Models 1996 And Newer Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?
      • Do Gm Vehicles Have A Passive Anti-theft System?
      • Do I Have To Transfer Anything From My Original Ecm/pcm?
      • Do I Need A Scanner To Reset The Anti-theft System
      • Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn.
      • No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application.
      • Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays.
      • Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module.
      • The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • What Are The Most Common Symptoms Of A Bad Pcm?
      • What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?
      • What’s The Difference Between An Ecm And A Pcm?
      • Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System.
      • “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission.
    • Features and Benefits:
      • Meets O.e. Fit And Function.
      • Meets Or Exceeds O.e.m Performance
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated, Computerized Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
    • Product Condition: Remanufactured
    • Terminal Quantity: 40, 40
  • CARDONE® Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design weaknesses. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant, and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back to peak performance.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
2000 - Chrysler Voyager V 6 Cyl 3.0L 181 2972
Cardone
2000 Chrysler Voyager Engine Control Module 6 Cyl 3.3L Cardone - Reman. Engine Control Computer

P311-0FA7C17    79-6251V  Remanufactured

4727279AB , 4727279AA , 04727279AB , 04727279AA

Qty:
$41.40 $161.78
Cardone Engine Control Module
  • Remanufactured Engine Control Computer
  • Vehicle specific Flash programming required ON or OFF the vehicle.Accurate VIN and mileage are req'd
  • Reman. Engine Control Computer
  • Product Attributes:
    • Connector/Terminal Configuration: Pin/male; Pin/male
    • FAQs:
      • Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Injection Pulse On Fuel Pump, Intermittent Starting Problems.
      • Chrysler Models 1996 And Newer Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?
      • Do Gm Vehicles Have A Passive Anti-theft System?
      • Do I Have To Transfer Anything From My Original Ecm/pcm?
      • Do I Need A Scanner To Reset The Anti-theft System
      • Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn.
      • No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application.
      • Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays.
      • Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module.
      • The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • What Are The Most Common Symptoms Of A Bad Pcm?
      • What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?
      • What’s The Difference Between An Ecm And A Pcm?
      • Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System.
      • “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission.
    • Features and Benefits:
      • Meets O.e. Fit And Function.
      • Meets Or Exceeds O.e.m Performance
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated, Computerized Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
    • Product Condition: Remanufactured
    • Terminal Quantity: 40, 40
  • CARDONE® Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design weaknesses. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant, and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back to peak performance.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
2000 - Chrysler Voyager V 6 Cyl 3.3L 201 3301
Cardone
2000 Chrysler Voyager Engine Control Module 6 Cyl 3.3L Cardone - Reman. Engine Control Computer

P311-4CCCC8F    79-7267V  Remanufactured

4727278AC , 04727278AC , 4727278AB

Qty:
$52.20 $198.43
Cardone Engine Control Module
  • Remanufactured Engine Control Computer
  • Vehicle specific Flash programming req'd ON or OFF the vehicle.Accurate VIN and mileage are req'd. Additional vehicle specific on-car programming must be performed AFTER installation to prevent drivability and starting issues.
  • Reman. Engine Control Computer
  • Product Attributes:
    • Connector/Terminal Configuration: Pin/male; Pin/male
    • FAQs:
      • Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Injection Pulse On Fuel Pump, Intermittent Starting Problems.
      • Chrysler Models 1996 And Newer Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?
      • Do Gm Vehicles Have A Passive Anti-theft System?
      • Do I Have To Transfer Anything From My Original Ecm/pcm?
      • Do I Need A Scanner To Reset The Anti-theft System
      • Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn.
      • No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application.
      • Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays.
      • Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module.
      • The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • What Are The Most Common Symptoms Of A Bad Pcm?
      • What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?
      • What’s The Difference Between An Ecm And A Pcm?
      • Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System.
      • “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission.
    • Features and Benefits:
      • Meets O.e. Fit And Function.
      • Meets Or Exceeds O.e.m Performance
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated, Computerized Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
    • Product Condition: Remanufactured
    • Terminal Quantity: 40, 40
  • CARDONE® Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design weaknesses. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant, and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back to peak performance.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
2000 - Chrysler Voyager V 6 Cyl 3.3L 201 3301
Cardone
2000 Chrysler Voyager Engine Control Module 4 Cyl 2.4L Cardone - Reman. Engine Control Computer

P311-2E7DD94    79-7274V  Remanufactured

4727274AC

Qty:
$41.40 $215.01
Cardone Engine Control Module
  • Remanufactured Engine Control Computer
  • Vehicle specific Flash programming required ON or OFF the vehicle.Accurate VIN and mileage are req'd
  • Reman. Engine Control Computer
  • Product Attributes:
    • Connector/Terminal Configuration: Pin/male; Pin/male
    • FAQs:
      • Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Injection Pulse On Fuel Pump, Intermittent Starting Problems.
      • Chrysler Models 1996 And Newer Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?
      • Do Gm Vehicles Have A Passive Anti-theft System?
      • Do I Have To Transfer Anything From My Original Ecm/pcm?
      • Do I Need A Scanner To Reset The Anti-theft System
      • Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn.
      • No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application.
      • Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays.
      • Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module.
      • The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • What Are The Most Common Symptoms Of A Bad Pcm?
      • What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?
      • What’s The Difference Between An Ecm And A Pcm?
      • Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System.
      • “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission.
    • Features and Benefits:
      • Meets O.e. Fit And Function.
      • Meets Or Exceeds O.e.m Performance
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated, Computerized Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
    • Product Condition: Remanufactured
    • Terminal Quantity: 40, 40
  • CARDONE® Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design weaknesses. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant, and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back to peak performance.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
2000 - Chrysler Voyager L 4 Cyl 2.4L 148 2429
Cardone
2000 Chrysler Voyager Engine Control Module 4 Cyl 2.4L Cardone - Reman. Engine Control Computer

P311-4C409DA    79-7266V  Remanufactured

4727275AB , 04727275AB , 04727275AA , 4727275AA

Qty:
$27.90 $194.34
Cardone Engine Control Module
  • Remanufactured Engine Control Computer
  • Vehicle specific Flash programming required ON or OFF the vehicle.Accurate VIN and mileage are req'd
  • Reman. Engine Control Computer
  • Product Attributes:
    • Connector/Terminal Configuration: Pin/male; Pin/male
    • FAQs:
      • Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Injection Pulse On Fuel Pump, Intermittent Starting Problems.
      • Chrysler Models 1996 And Newer Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?
      • Do Gm Vehicles Have A Passive Anti-theft System?
      • Do I Have To Transfer Anything From My Original Ecm/pcm?
      • Do I Need A Scanner To Reset The Anti-theft System
      • Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn.
      • No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application.
      • Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays.
      • Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module.
      • The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • What Are The Most Common Symptoms Of A Bad Pcm?
      • What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?
      • What’s The Difference Between An Ecm And A Pcm?
      • Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System.
      • “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission.
    • Features and Benefits:
      • Meets O.e. Fit And Function.
      • Meets Or Exceeds O.e.m Performance
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated, Computerized Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
    • Product Condition: Remanufactured
    • Terminal Quantity: 40, 40
  • CARDONE® Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design weaknesses. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant, and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back to peak performance.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
2000 - Chrysler Voyager L 4 Cyl 2.4L 148 2429

Showing 1 - 6 of 6 Products for Engine Control Module.