802.589.0911 Live Chat With Us

Showing Products For 1996 Isuzu Hombre Engine Control Module

Below are all the different brands and applications for 1996 Isuzu Hombre Engine Control Module

Showing 1 - 1 of 1 Products for Engine Control Module.

Refine Your Search

Cardone
1996 Isuzu Hombre Engine Control Module Cardone - Reman. Powertrain Control Module

P311-5DC7369    77-5830F  Remanufactured

16231851 , 8162158300 , 16215830

Qty:
$93.16
Cardone Engine Control Module
  • Remanufactured Powertrain Control Module
  • I.D. #(s) 16215830; Vehicle specific Flash programming req'd ON or OFF the vehicle.Accurate VIN and mileage are req'd. Additional vehicle specific on-car programming must be performed AFTER installation to prevent drivability and starting issues. Knock Module must be removed from original PCM and installed in replacement PCM
  • Reman. Powertrain Control Module
  • Product Attributes:
    • Connector/Terminal Configuration: Pin/male; Pin/male; Pin/male
    • FAQs:
      • “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission.
      • Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Injection Pulse On Fuel Pump, Intermittent Starting Problems.
      • Chrysler Models 1996 And Newer Will Need To Be Vin Programmed.
      • Chrysler Pcm's Identified With A "v" Suffix Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti Theft System (p.a.t.s) Reset?
      • Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?
      • Do Gm Vehicles Have A Passive Anti-theft System?
      • Do I Have To Transfer Anything From My Original Ecm/pcm?
      • Do I Need A Scanner To Reset The Anti-theft System
      • Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn.
      • I Replaced The Pcm In My Gm Vehicle. Do I Need To Reset The Passlock Or Passkey Vehicle Anti Theft System (vats)?
      • No, Not All Ford Vehicles Require A Pats Reset. Check The Pats Chart Found On The Motorcraft Site For Your Application.
      • No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application.
      • Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Areas That Cause Failures Are: Poor Grounds And Powers, Bad Wiring Harness, Shorted Solenoids/relays.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays.
      • Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module.
      • The Replacement Ecm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • The Wrong Ecm May Have Been Installed. Verify The Ford Engineering Id Number, Found On The Ecm/pcm, Crosses To The Correct Cardone Number.
      • What Are The Most Common Symptoms Of A Bad Pcm?
      • What Steps Should I Take To Assure The Original Ecm/pcm Is Causing The Issue?
      • What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?
      • What’s The Difference Between An Ecm And A Pcm?
      • Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System.
      • Yes, There's A 10 Minute Procedure Utilizing A Tech 2 Scanner And A Gm Terminal Subscription. There Is Also A 30 Minute Manual Procedure That Can Be Done Without A Scanner. Refer To An Oe Approved Service Manual For Either Option.
    • Features and Benefits:
      • As A Remanufactured Original Equipment Part, This Unit Guarantees A Perfect Vehicle Fit.
      • Meets O.e. Fit And Function.
      • Meets Or Exceeds O.e.m Performance
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Our Remanufacturing Process Is Earth-friendly, As It Reduces The Energy And Raw Material Needed To Make A New Part By 80%.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated, Computerized Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
    • Product Condition: Remanufactured
  • CARDONE® Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design weaknesses. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant, and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back to peak performance.
Brand: Cardone
Additional Fitment Information:
Vehicle
1996 - Isuzu Hombre

Showing 1 - 1 of 1 Products for Engine Control Module.