802.589.0911 Live Chat With Us

Finish Selecting Your Vehicle

Choose your Engine for your 1994 GMC C3500

  • 8 Cyl 5.7L
  • 8 Cyl 6.5L
  • 8 Cyl 7.4L

Showing Products For 1994 GMC C3500 Engine Control Module

Below are all the different brands and applications for 1994 GMC C3500 Engine Control Module

Showing 1 - 5 of 5 Products for Engine Control Module.

Refine Your Search

Cardone
1994 GMC C3500 Engine Control Module 8 Cyl 7.4L Cardone - Reman. A-1 CARDONE Powertrain Control Module

P311-20B8588    77-7427  Remanufactured

16197427

Qty:
$49.50 $92.04
Cardone Engine Control Module
  • Remanufactured Powertrain Control Module
  • The PROM(s)/CALPACK must be transferred from the original module to the replacement module.
  • Reman. A-1 CARDONE Powertrain Control Module
  • Product Attributes:
    • Connector/Terminal Configuration: Pin/male; Pin/male
    • E-Waste: Yes
    • FAQs:
      • Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Injection Pulse On Fuel Pump, Intermittent Starting Problems.
      • Chrysler Models 1996 And Newer Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?
      • Do Gm Vehicles Have A Passive Anti-theft System?
      • Do I Have To Transfer Anything From My Original Ecm/pcm?
      • Do I Need A Scanner To Reset The Anti-theft System
      • Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn.
      • No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application.
      • Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays.
      • Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module.
      • The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • What Are The Most Common Symptoms Of A Bad Pcm?
      • What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?
      • What’s The Difference Between An Ecm And A Pcm?
      • Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System.
      • “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission.
    • Features and Benefits:
      • Meets O.e. Fit And Function.
      • Meets Or Exceeds O.e.m Performance
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated, Computerized Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
    • Housing Material: Metal
    • Product Condition: Remanufactured
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design flaws. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back on the road with our remanufactured electronic and powertrain control modules.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
1994 - GMC C3500 V 8 Cyl 7.4L 454 -
Cardone
1994 GMC C3500 Engine Control Module 8 Cyl 7.4L Cardone - Reman. A-1 CARDONE Engine Control Computer

P311-5B7EE87    77-6395  Remanufactured

16196395

Qty:
$22.50 $105.45
Cardone Engine Control Module
  • Remanufactured Engine Control Computer
  • The PROM(s)/CALPACK must be transferred from the original module to the replacement module.
  • Reman. A-1 CARDONE Engine Control Computer
  • Product Attributes:
    • Connector/Terminal Configuration: Pin/male; Pin/male
    • E-Waste: Yes
    • FAQs:
      • Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Injection Pulse On Fuel Pump, Intermittent Starting Problems.
      • Chrysler Models 1996 And Newer Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?
      • Do Gm Vehicles Have A Passive Anti-theft System?
      • Do I Have To Transfer Anything From My Original Ecm/pcm?
      • Do I Need A Scanner To Reset The Anti-theft System
      • Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn.
      • No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application.
      • Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays.
      • Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module.
      • The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • What Are The Most Common Symptoms Of A Bad Pcm?
      • What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?
      • What’s The Difference Between An Ecm And A Pcm?
      • Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System.
      • “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission.
    • Features and Benefits:
      • Meets O.e. Fit And Function.
      • Meets Or Exceeds O.e.m Performance
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated, Computerized Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
    • Housing Material: Metal
    • Product Condition: Remanufactured
    • Removable PROM: Yes
    • Terminal Quantity: 32, 32
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design flaws. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back on the road with our remanufactured electronic and powertrain control modules.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
1994 - GMC C3500 V 8 Cyl 7.4L 454 -
Cardone
1994 GMC C3500 Engine Control Module 8 Cyl 5.7L Cardone - Reman. A-1 CARDONE Powertrain Control Module

P311-0B70DAA    77-8625  Remanufactured

16168625

Qty:
$33.30 $92.04
Cardone Engine Control Module
  • Remanufactured Powertrain Control Module
  • The PROM(s)/CALPACK must be transferred from the original module to the replacement module.
  • Reman. A-1 CARDONE Powertrain Control Module
  • Product Attributes:
    • Connector/Terminal Configuration: Pin/male; Pin/male
    • E-Waste: Yes
    • FAQs:
      • Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Injection Pulse On Fuel Pump, Intermittent Starting Problems.
      • Chrysler Models 1996 And Newer Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?
      • Do Gm Vehicles Have A Passive Anti-theft System?
      • Do I Have To Transfer Anything From My Original Ecm/pcm?
      • Do I Need A Scanner To Reset The Anti-theft System
      • Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn.
      • No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application.
      • Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays.
      • Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module.
      • The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • What Are The Most Common Symptoms Of A Bad Pcm?
      • What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?
      • What’s The Difference Between An Ecm And A Pcm?
      • Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System.
      • “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission.
    • Features and Benefits:
      • Meets O.e. Fit And Function.
      • Meets Or Exceeds O.e.m Performance
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated, Computerized Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
    • Housing Material: Metal
    • Product Condition: Remanufactured
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design flaws. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back on the road with our remanufactured electronic and powertrain control modules.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
1994 - GMC C3500 V 8 Cyl 5.7L 350 -
Cardone
1994 GMC C3500 Engine Control Module 8 Cyl 5.7L Cardone - Reman. A-1 CARDONE Engine Control Computer

P311-4CDED72    77-6396  Remanufactured

16196396 , 16200269

Qty:
$92.04
Cardone Engine Control Module
  • Remanufactured Engine Control Computer
  • The PROM(s)/CALPACK must be transferred from the original module to the replacement module.
  • Reman. A-1 CARDONE Engine Control Computer
  • Product Attributes:
    • Connector/Terminal Configuration: Pin/male; Pin/male
    • E-Waste: Yes
    • FAQs:
      • Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Injection Pulse On Fuel Pump, Intermittent Starting Problems.
      • Chrysler Models 1996 And Newer Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?
      • Do Gm Vehicles Have A Passive Anti-theft System?
      • Do I Have To Transfer Anything From My Original Ecm/pcm?
      • Do I Need A Scanner To Reset The Anti-theft System
      • Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn.
      • No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application.
      • Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays.
      • Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module.
      • The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • What Are The Most Common Symptoms Of A Bad Pcm?
      • What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?
      • What’s The Difference Between An Ecm And A Pcm?
      • Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System.
      • “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission.
    • Features and Benefits:
      • Meets O.e. Fit And Function.
      • Meets Or Exceeds O.e.m Performance
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated, Computerized Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
    • Housing Material: Metal
    • Product Condition: Remanufactured
    • Removable PROM: Yes
    • Terminal Quantity: 32, 24
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design flaws. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back on the road with our remanufactured electronic and powertrain control modules.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
1994 - GMC C3500 V 8 Cyl 5.7L 350 -
Cardone
1994 GMC C3500 Engine Control Module 8 Cyl 6.5L Cardone - Reman. A-1 CARDONE Powertrain Control Module

P311-1E80321    77-3977  Remanufactured

16183977

Qty:
$33.30 $97.92
Cardone Engine Control Module
  • Remanufactured Powertrain Control Module
  • The PROM(s)/CALPACK must be transferred from the original module to the replacement module.
  • Reman. A-1 CARDONE Powertrain Control Module
  • Product Attributes:
    • Connector/Terminal Configuration: Pin/male; Pin/male; Pin/male
    • E-Waste: Yes
    • FAQs:
      • Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Injection Pulse On Fuel Pump, Intermittent Starting Problems.
      • Chrysler Models 1996 And Newer Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?
      • Do Gm Vehicles Have A Passive Anti-theft System?
      • Do I Have To Transfer Anything From My Original Ecm/pcm?
      • Do I Need A Scanner To Reset The Anti-theft System
      • Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn.
      • No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application.
      • Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays.
      • Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module.
      • The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • What Are The Most Common Symptoms Of A Bad Pcm?
      • What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?
      • What’s The Difference Between An Ecm And A Pcm?
      • Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System.
      • “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission.
    • Features and Benefits:
      • Meets O.e. Fit And Function.
      • Meets Or Exceeds O.e.m Performance
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated, Computerized Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
    • Housing Material: Metal
    • Product Condition: Remanufactured
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design flaws. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back on the road with our remanufactured electronic and powertrain control modules.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
1994 - GMC C3500 V 8 Cyl 6.5L 395 -

Showing 1 - 5 of 5 Products for Engine Control Module.