Finish Selecting Your Vehicle

Choose your Engine for your 1992 GMC G3500

  • 6 Cyl 4.3L
  • 8 Cyl 5.7L
  • 8 Cyl 7.4L

Shop By Brand

The Following brands are available based on your search.

  • ACDelco
    ACDelco
  • Cardone
    Cardone
  • Holley
    Holley
  • Painless Wiring
    Painless Wiring
  • Standard Ignition
    Standard Ignition

Showing Products For 1992 GMC G3500 Engine Control Module

Below are all the different brands and applications for 1992 GMC G3500 Engine Control Module

Showing 1 - 10 of 28 Products for Engine Control Module.

Refine Your Search

Cardone
1992 GMC G3500 Engine Control Module 6 Cyl 4.3L Cardone - Engine Control Module

P311-05E9A17    77-7060  Remanufactured

Qty:
In Stock & Ready to Ship
$74.70 $111.18
Cardone Engine Control Module
  • with Original Equipment (OE) # 16147060 The PROM(s)/CALPACK must be transferred from the original module to the replacement module Additional relearns (theft, crankshaft, idle, etc) may be required
  • Engine Control Module
  • Product Attributes:
    • FAQs:
      • Chrysler Pcm's Identified With A "v" Suffix Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti Theft System (p.a.t.s) Reset?
      • I Replaced The Pcm In My Gm Vehicle. Do I Need To Reset The Passlock Or Passkey Vehicle Anti Theft System (vats)?
      • No, Not All Ford Vehicles Require A Pats Reset. Check The Pats Chart Found On The Motorcraft Site For Your Application.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Areas That Cause Failures Are: Poor Grounds And Powers, Bad Wiring Harness, Shorted Solenoids/relays.
      • The Replacement Ecm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • The Wrong Ecm May Have Been Installed. Verify The Ford Engineering Id Number, Found On The Ecm/pcm, Crosses To The Correct Cardone Number.
      • What Steps Should I Take To Assure The Original Ecm/pcm Is Causing The Issue?
      • Yes, There's A 10 Minute Procedure Utilizing A Tech 2 Scanner And A Gm Terminal Subscription. There Is Also A 30 Minute Manual Procedure That Can Be Done Without A Scanner. Refer To An Oe Approved Service Manual For Either Option.
    • Features and Benefits:
      • As A Remanufactured Original Equipment Part, This Unit Guarantees A Perfect Vehicle Fit.
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Our Remanufacturing Process Is Earth-friendly, As It Reduces The Energy And Raw Material Needed To Make A New Part By 80%.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated Computer Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design weaknesses. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant, and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back to peak performance.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
1992 - GMC G3500 V 6 Cyl 4.3L 262 -
Cardone
1992 GMC G3500 Engine Control Module 8 Cyl 7.4L Cardone - Engine Control Module

P311-05E9A17    77-7060  Remanufactured

16147060

Qty:
In Stock & Ready to Ship
$74.70 $111.18
Cardone Engine Control Module
  • The PROM(s)/CALPACK must be transferred from the original module to the replacement module Additional relearns (theft, crankshaft, idle, etc) may be required
  • Engine Control Module
  • Product Attributes:
    • FAQs:
      • Chrysler Pcm's Identified With A "v" Suffix Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti Theft System (p.a.t.s) Reset?
      • I Replaced The Pcm In My Gm Vehicle. Do I Need To Reset The Passlock Or Passkey Vehicle Anti Theft System (vats)?
      • No, Not All Ford Vehicles Require A Pats Reset. Check The Pats Chart Found On The Motorcraft Site For Your Application.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Areas That Cause Failures Are: Poor Grounds And Powers, Bad Wiring Harness, Shorted Solenoids/relays.
      • The Replacement Ecm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • The Wrong Ecm May Have Been Installed. Verify The Ford Engineering Id Number, Found On The Ecm/pcm, Crosses To The Correct Cardone Number.
      • What Steps Should I Take To Assure The Original Ecm/pcm Is Causing The Issue?
      • Yes, There's A 10 Minute Procedure Utilizing A Tech 2 Scanner And A Gm Terminal Subscription. There Is Also A 30 Minute Manual Procedure That Can Be Done Without A Scanner. Refer To An Oe Approved Service Manual For Either Option.
    • Features and Benefits:
      • As A Remanufactured Original Equipment Part, This Unit Guarantees A Perfect Vehicle Fit.
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Our Remanufacturing Process Is Earth-friendly, As It Reduces The Energy And Raw Material Needed To Make A New Part By 80%.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated Computer Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design weaknesses. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant, and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back to peak performance.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
1992 - GMC G3500 V 8 Cyl 7.4L 454 -
Cardone
1992 GMC G3500 Engine Control Module 6 Cyl 4.3L Cardone - Engine Control Module

P311-15A1CDD    77-4288  Remanufactured

16144288

Qty:
In Stock & Ready to Ship
$103.69
Cardone Engine Control Module
  • with Original Equipment (OE) # 16144288 The PROM(s)/CALPACK must be transferred from the original module to the replacement module Additional relearns (theft, crankshaft, idle, etc) may be required
  • Engine Control Module
  • Product Attributes:
    • FAQs:
      • Chrysler Pcm's Identified With A "v" Suffix Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti Theft System (p.a.t.s) Reset?
      • I Replaced The Pcm In My Gm Vehicle. Do I Need To Reset The Passlock Or Passkey Vehicle Anti Theft System (vats)?
      • No, Not All Ford Vehicles Require A Pats Reset. Check The Pats Chart Found On The Motorcraft Site For Your Application.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Areas That Cause Failures Are: Poor Grounds And Powers, Bad Wiring Harness, Shorted Solenoids/relays.
      • The Replacement Ecm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • The Wrong Ecm May Have Been Installed. Verify The Ford Engineering Id Number, Found On The Ecm/pcm, Crosses To The Correct Cardone Number.
      • What Steps Should I Take To Assure The Original Ecm/pcm Is Causing The Issue?
      • Yes, There's A 10 Minute Procedure Utilizing A Tech 2 Scanner And A Gm Terminal Subscription. There Is Also A 30 Minute Manual Procedure That Can Be Done Without A Scanner. Refer To An Oe Approved Service Manual For Either Option.
    • Features and Benefits:
      • As A Remanufactured Original Equipment Part, This Unit Guarantees A Perfect Vehicle Fit.
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Our Remanufacturing Process Is Earth-friendly, As It Reduces The Energy And Raw Material Needed To Make A New Part By 80%.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated Computer Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design weaknesses. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant, and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back to peak performance.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
1992 - GMC G3500 V 6 Cyl 4.3L 262 -
ACDelco
1992 GMC G3500 Engine Control Module 8 Cyl 7.4L ACDelco

P311-1CAD18F    88999179  Remanufactured

Qty:
In Stock & Ready to Ship
$90.00 $233.97
ACDelco Engine Control Module
  • Remanufactured
Brand: ACDelco
Additional Fitment Information:
Vehicle Engine Designation Engine VIN Block Engine
1992 - GMC G3500 L19 N V 8 Cyl 7.4L
ACDelco
1992 GMC G3500 Engine Control Module 6 Cyl 4.3L ACDelco

P311-1CAD18F    88999179  Remanufactured

Qty:
In Stock & Ready to Ship
$90.00 $233.97
ACDelco Engine Control Module
  • Remanufactured; 4.10R (GT5), EMISSIONS SYSTEM (UNDER 8500 LB GVW) (NA1)
Brand: ACDelco
Additional Fitment Information:
Vehicle Transmission Engine Designation Trans. Speed Engine VIN Transmission Manuf. Code Block Engine
1992 - GMC G3500 Automatic LB4 4 Z 4L80-E V 6 Cyl 4.3L
ACDelco
1992 GMC G3500 Engine Control Module 8 Cyl 5.7L ACDelco

P311-1CAD18F    88999179  Remanufactured

Qty:
In Stock & Ready to Ship
$90.00 $233.97
ACDelco Engine Control Module
  • Remanufactured; EXCEPT LEADED FUEL EMISSIONS EXPORT (NM8), ELECTRIC SPEED GOVERNOR 70MPH (9B9), SPEED GOVERNOR 65MPH (9C2)
Brand: ACDelco
Additional Fitment Information:
Vehicle Transmission Trans. Speed Engine VIN Transmission Manuf. Code Block Engine
1992 - GMC G3500 Automatic 4 K 4L80-E V 8 Cyl 5.7L
ACDelco
1992 GMC G3500 Engine Control Module 6 Cyl 4.3L ACDelco

P311-1CAD18F    88999179  Remanufactured

Qty:
In Stock & Ready to Ship
$90.00 $233.97
ACDelco Engine Control Module
  • Remanufactured; EMISSIONS SYSTEM (ABOVE 8500 LB GVW) (NA4)
Brand: ACDelco
Additional Fitment Information:
Vehicle Transmission Engine Designation Trans. Speed Engine VIN Transmission Manuf. Code Block Engine
1992 - GMC G3500 Automatic LB4 4 Z 4L80-E V 6 Cyl 4.3L
ACDelco
1992 GMC G3500 Engine Control Module 6 Cyl 4.3L ACDelco

P311-1CAD18F    88999179  Remanufactured

Qty:
In Stock & Ready to Ship
$90.00 $233.97
ACDelco Engine Control Module
  • Remanufactured; 4.56R (HC4), EMISSIONS SYSTEM (UNDER 8500 LB GVW) (NA1)
Brand: ACDelco
Additional Fitment Information:
Vehicle Transmission Engine Designation Trans. Speed Engine VIN Transmission Manuf. Code Block Engine
1992 - GMC G3500 Automatic LB4 4 Z 4L80-E V 6 Cyl 4.3L
ACDelco
1992 GMC G3500 Engine Control Module 8 Cyl 5.7L ACDelco

P311-1CAD18F    88999179  Remanufactured

Qty:
In Stock & Ready to Ship
$90.00 $233.97
ACDelco Engine Control Module
  • Remanufactured; SPEED GOVERNOR 65MPH (9C2)
Brand: ACDelco
Additional Fitment Information:
Vehicle Engine VIN Block Engine
1992 - GMC G3500 K V 8 Cyl 5.7L
Standard Ignition
Engine Control Module Standard Ignition

P311-429B8DC    EM2A  Remanufactured

Qty:
In Stock & Ready to Ship
$226.69
Standard Ignition Engine Control Module
  • Engine Control Computer
  • Product Attributes:
    • Connector Gender: Female
    • Connector Quantity: 2
    • Contents: Sensor Simulator Tester
    • Terminal Type: Wire Lead
  • Featuring the broadest sensor coverage in the market, we meet the service professionals needs with the highest quality product every time he opens the box. As a global manufacturer of emission components, complete quality control is maintained through the manufacturing process from componentry to finished product.

  • This is a Universal/Non Application Specific Product. To install this part, you made need to cut, weld, or make other modifications to your vehicle.
Brand: Standard Ignition
Additional Fitment Information:
Vehicle

Showing 1 - 10 of 28 Products for Engine Control Module.