1987 Chevrolet Caprice Ignition Control Module Ignition - ACDelco, Accel, Autopart International, CARQUEST, Delphi, Holley, MSD, Mallory, Pertronix, Proform, Standard Ignition, True Tech

Ignition Control Module MSD

Part # P311-0307556 Manu # 62023 Condition: New

Qty:

In Stock & Ready to Ship

Best Price: $338.31

Ultra 6A Ignition Box
Ultra 6A Ignition Box; Black; Compatible w/4/6/8 Cylinder Engines w/Distributor; 1.1 Amp Per 1000RPM; 520-540 Volts;
Product Attributes:
- RPM: 15000
- WARNING CA Proposition 65: Yes
- WARNING CA Proposition 65 Message: Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
Features:
- Plug-N-Play
- New Processor And Board Design Provide A Highly Efficient Ignition
- 60 Percent Smaller And 50 Percent Lighter Than The Msd Digital 6A
- Powerful Capacitive Discharge Of Multiple Sparks Improves Performance
- Consistently High Spark Energy Of 135Mj To 150Mj For Every Firing - From Idle To Redline Rpm
- Operates On Most 7 To 28-Volt Electrical Systems
- Connects To Points And Magnetic Pickups
- Fully Protected Against An Open Coil - Shorted Coil And Open Load
- Quickens Throttle Response And Improves Starting
- Tach Output To Drive An External Tachometer
The Ultra 6A Series continues to use a high speed controller that can make extremely quick compensations to the output voltage, multiple spark series, timing and rpm limits while maintaining precise timing and accurate rev limiting. The circuits and controller of the MSD have been thoroughly filtered to create protection against Electro Magnetic Interference (EMI).The Ultra 6A Series feature a capacitive discharge ignition design. The majority of stock ignition systems are inductive ignitions. In an inductive ignition, the coil must store and step up the voltage to maximum strength in between each firing. At higher rpm, since there is less time to charge the coil to full capacity, the voltage falls short of reaching maximum energy which results in a loss of power or top end miss.

Fitment Warning:
This is a Universal/Non Application Specific Product. To install this part, you made need to cut, weld, or make other modifications to your vehicle.

Brand: MSD

Vehicle

Ignition Control Module MSD

Part # P311-1FC27D5 Manu # 6202 Condition: New

Qty:

In Stock & Ready to Ship

Best Price: $348.26

Ultra 6A Ignition Box
Ultra 6A Ignition Box; Red; Compatible w/4/6/8 Cylinder Engines w/Distributor; 1.1 Amp Per 1000RPM; 520-540 Volts;
Product Attributes:
- RPM: 15000
- WARNING CA Proposition 65: Yes
- WARNING CA Proposition 65 Message: Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
Features:
- Plug-N-Play
- New Processor And Board Design Provide A Highly Efficient Ignition
- 60 Percent Smaller And 50 Percent Lighter Than The Msd Digital 6A
- Powerful Capacitive Discharge Of Multiple Sparks Improves Performance
- Consistently High Spark Energy Of 135Mj To 150Mj For Every Firing - From Idle To Redline Rpm
- Operates On Most 7 To 28-Volt Electrical Systems
- Connects To Points And Magnetic Pickups
- Fully Protected Against An Open Coil - Shorted Coil And Open Load
- Quickens Throttle Response And Improves Starting
- Tach Output To Drive An External Tachometer
The Ultra 6A Series continues to use a high speed controller that can make extremely quick compensations to the output voltage, multiple spark series, timing and rpm limits while maintaining precise timing and accurate rev limiting. The circuits and controller of the MSD have been thoroughly filtered to create protection against Electro Magnetic Interference (EMI).The Ultra 6A Series feature a capacitive discharge ignition design. The majority of stock ignition systems are inductive ignitions. In an inductive ignition, the coil must store and step up the voltage to maximum strength in between each firing. At higher rpm, since there is less time to charge the coil to full capacity, the voltage falls short of reaching maximum energy which results in a loss of power or top end miss.

Fitment Warning:
This is a Universal/Non Application Specific Product. To install this part, you made need to cut, weld, or make other modifications to your vehicle.

Brand: MSD

Vehicle

Ignition Control Module Standard Ignition

Part # P311-2238A1A Manu # LX-1064 Condition: New

This Part Fits the Following OEM/Substitute Numbers: 18-5764 , 55-2128 , 582261 , 586696 , 6H1462 , CBC1501 , CBE2114 , MC199 , TP564

Qty:

In Stock & Ready to Ship

Best Price: $142.60

Ignition Control Module
Product Attributes:
- Connector Gender: Female
- Connector Quantity: 4
- Terminal Gender: Male
- Terminal Quantity: 5
- Terminal Type: Pins
Our control modules feature double wire bonds for better connections, greater dependability and longer life despite being subjected to intense vibration and the tough operating environment. Copper slug heat sinks provide better heat dissipation to prevent heat from damaging the module. Our ignition modules will respond to a weak signal from the crankshaft position sensor and begin energizing the coils immediately for better starts in cold weather. High-temperature polymer housing reducing moisture intrusion and minimizes vibration damage for extended life and improved reliability. Our ignition modules are durability tested for 500 thermal cycles ranging from -40C to +125C. With industry leading expertise in electronic ignition, when original equipment fails our products are designed to fix the inherent failure issues. As a global manufacturer of original equipment ignition products, we maintain complete quality control throughout the manufacturing process from componentry to finished product.

Fitment Warning:
This is a Universal/Non Application Specific Product. To install this part, you made need to cut, weld, or make other modifications to your vehicle.

Brand: Standard Ignition

Vehicle

Ignition Control Module Standard Ignition

Part # P311-322C02D Manu # LX-1070 Condition: New

This Part Fits the Following OEM/Substitute Numbers: 18-5770 , 55-2122 , 584027 , 584028 , 6H1456 , CBC1518 , CBE2120 , MC193 , TP570

Qty:

In Stock & Ready to Ship

Best Price: $172.21

Ignition Control Module
Product Attributes:
- Connector Gender: Female
- Terminal Gender: Male
- Terminal Quantity: 5
- Terminal Type: Blade
Our control modules feature double wire bonds for better connections, greater dependability and longer life despite being subjected to intense vibration and the tough operating environment. Copper slug heat sinks provide better heat dissipation to prevent heat from damaging the module. Our ignition modules will respond to a weak signal from the crankshaft position sensor and begin energizing the coils immediately for better starts in cold weather. High-temperature polymer housing reducing moisture intrusion and minimizes vibration damage for extended life and improved reliability. Our ignition modules are durability tested for 500 thermal cycles ranging from -40C to +125C. With industry leading expertise in electronic ignition, when original equipment fails our products are designed to fix the inherent failure issues. As a global manufacturer of original equipment ignition products, we maintain complete quality control throughout the manufacturing process from componentry to finished product.

Fitment Warning:
This is a Universal/Non Application Specific Product. To install this part, you made need to cut, weld, or make other modifications to your vehicle.

Brand: Standard Ignition

Vehicle

Ignition Control Module Standard Ignition

Part # P311-1BF3CB2 Manu # LX-1073 Condition: New

This Part Fits the Following OEM/Substitute Numbers: 18-5774 , 19161989 , 5004532 , 55-2119 , 585145 , 6H1453 , CBC1514 , CBE2123 , MC190 , TP573 , U1998C

Qty:

In Stock & Ready to Ship

Best Price: $281.66

Ignition Control Module
Product Attributes:
- Connector Gender: Female + Male
- Connector Quantity: 7
- Mounting Location: External
- Terminal Gender: Male; Female
- Terminal Quantity: 10
- Terminal Type: Blade & Pin
Our control modules feature double wire bonds for better connections, greater dependability and longer life despite being subjected to intense vibration and the tough operating environment. Copper slug heat sinks provide better heat dissipation to prevent heat from damaging the module. Our ignition modules will respond to a weak signal from the crankshaft position sensor and begin energizing the coils immediately for better starts in cold weather. High-temperature polymer housing reducing moisture intrusion and minimizes vibration damage for extended life and improved reliability. Our ignition modules are durability tested for 500 thermal cycles ranging from -40C to +125C. With industry leading expertise in electronic ignition, when original equipment fails our products are designed to fix the inherent failure issues. As a global manufacturer of original equipment ignition products, we maintain complete quality control throughout the manufacturing process from componentry to finished product.

Fitment Warning:
This is a Universal/Non Application Specific Product. To install this part, you made need to cut, weld, or make other modifications to your vehicle.

Brand: Standard Ignition

Vehicle

Ignition Control Module Standard Ignition

Part # P311-2D5F7F3 Manu # LX-1075 Condition: New

This Part Fits the Following OEM/Substitute Numbers: 18-5781 , 55-2117 , 586661 , 6H1451 , CBE2125 , MC188 , TP575

Qty:

In Stock & Ready to Ship

Best Price: $211.48

Ignition Control Module
Product Attributes:
- Connector Gender: Female
- Connector Quantity: 2
- Terminal Gender: Male
- Terminal Quantity: 4
- Terminal Type: Pins
Our control modules feature double wire bonds for better connections, greater dependability and longer life despite being subjected to intense vibration and the tough operating environment. Copper slug heat sinks provide better heat dissipation to prevent heat from damaging the module. Our ignition modules will respond to a weak signal from the crankshaft position sensor and begin energizing the coils immediately for better starts in cold weather. High-temperature polymer housing reducing moisture intrusion and minimizes vibration damage for extended life and improved reliability. Our ignition modules are durability tested for 500 thermal cycles ranging from -40C to +125C. With industry leading expertise in electronic ignition, when original equipment fails our products are designed to fix the inherent failure issues. As a global manufacturer of original equipment ignition products, we maintain complete quality control throughout the manufacturing process from componentry to finished product.

Fitment Warning:
This is a Universal/Non Application Specific Product. To install this part, you made need to cut, weld, or make other modifications to your vehicle.

Brand: Standard Ignition

Vehicle

Ignition Control Module Standard Ignition

Part # P311-2992AAD Manu # LX-1077 Condition: New

This Part Fits the Following OEM/Substitute Numbers: 18-5783 , 55-2115 , 582811 , 6H1449 , 763794 , CBC1523 , CBE2127 , MC186 , TP577

Qty:

In Stock & Ready to Ship

Best Price: $175.50

Ignition Control Module
Product Attributes:
- Connector Gender: Female
- Connector Quantity: 5
- Terminal Gender: Male
- Terminal Quantity: 5
- Terminal Type: Pin Plug
Our control modules feature double wire bonds for better connections, greater dependability and longer life despite being subjected to intense vibration and the tough operating environment. Copper slug heat sinks provide better heat dissipation to prevent heat from damaging the module. Our ignition modules will respond to a weak signal from the crankshaft position sensor and begin energizing the coils immediately for better starts in cold weather. High-temperature polymer housing reducing moisture intrusion and minimizes vibration damage for extended life and improved reliability. Our ignition modules are durability tested for 500 thermal cycles ranging from -40C to +125C. With industry leading expertise in electronic ignition, when original equipment fails our products are designed to fix the inherent failure issues. As a global manufacturer of original equipment ignition products, we maintain complete quality control throughout the manufacturing process from componentry to finished product.

Fitment Warning:
This is a Universal/Non Application Specific Product. To install this part, you made need to cut, weld, or make other modifications to your vehicle.

Brand: Standard Ignition

Vehicle

Ignition Control Module Standard Ignition

Part # P311-549C958 Manu # LX-1078 Condition: New

This Part Fits the Following OEM/Substitute Numbers: 18-5784 , 55-2114 , 583110 , 6H1448 , CBC1524 , CBE2128 , MC185 , TP578

Qty:

In Stock & Ready to Ship

Best Price: $157.33

Ignition Control Module
Product Attributes:
- Connector Gender: Female; Female
- Connector Quantity: 3
- Mounting Location: Distributor
- Terminal Gender: Male
- Terminal Quantity: 9
- Terminal Type: Pin
Our control modules feature double wire bonds for better connections, greater dependability and longer life despite being subjected to intense vibration and the tough operating environment. Copper slug heat sinks provide better heat dissipation to prevent heat from damaging the module. Our ignition modules will respond to a weak signal from the crankshaft position sensor and begin energizing the coils immediately for better starts in cold weather. High-temperature polymer housing reducing moisture intrusion and minimizes vibration damage for extended life and improved reliability. Our ignition modules are durability tested for 500 thermal cycles ranging from -40C to +125C. With industry leading expertise in electronic ignition, when original equipment fails our products are designed to fix the inherent failure issues. As a global manufacturer of original equipment ignition products, we maintain complete quality control throughout the manufacturing process from componentry to finished product.

Fitment Warning:
This is a Universal/Non Application Specific Product. To install this part, you made need to cut, weld, or make other modifications to your vehicle.

Brand: Standard Ignition

Vehicle

Ignition Control Module Standard Ignition

Part # P311-4F146EE Manu # LX-913 Condition: New

This Part Fits the Following OEM/Substitute Numbers: 19145718 , 339-7452A1 , 339-7452A2 , 339-7452A3 , 3397452A1 , 3397452A3 , 55-2101 , 899883230 , CBE2101 , MC172 , TP593 , U1980C

Qty:

In Stock & Ready to Ship

Best Price: $206.84

Ignition Control Module
Product Attributes:
- Connector Gender: No Connector
- Connector Quantity: 2
- Mounting Location: External
- Terminal Gender: Male
- Terminal Quantity: 6; 1
- Terminal Type: Pin; Eye Ring
Our control modules feature double wire bonds for better connections, greater dependability and longer life despite being subjected to intense vibration and the tough operating environment. Copper slug heat sinks provide better heat dissipation to prevent heat from damaging the module. Our ignition modules will respond to a weak signal from the crankshaft position sensor and begin energizing the coils immediately for better starts in cold weather. High-temperature polymer housing reducing moisture intrusion and minimizes vibration damage for extended life and improved reliability. Our ignition modules are durability tested for 500 thermal cycles ranging from -40C to +125C. With industry leading expertise in electronic ignition, when original equipment fails our products are designed to fix the inherent failure issues. As a global manufacturer of original equipment ignition products, we maintain complete quality control throughout the manufacturing process from componentry to finished product.

Fitment Warning:
This is a Universal/Non Application Specific Product. To install this part, you made need to cut, weld, or make other modifications to your vehicle.

Brand: Standard Ignition

Vehicle

Ignition Control Module Standard Ignition

Part # P311-44C5A3F Manu # LX-917 Condition: New

This Part Fits the Following OEM/Substitute Numbers: 18-5881 , 332-5772A1 , 332-5772A2 , 332-5772A3 , 332-5772A5 , 3325772A1 , 3325772A7 , 55-2097 , CBE2107 , F720301 , MC168 , TP597

Qty:

In Stock & Ready to Ship

Best Price: $307.33

Ignition Control Module
Product Attributes:
- Connector Gender: Female
- Mounting Location: Internal
- Terminal Gender: Male
- Terminal Quantity: 13
- Terminal Type: Pin + Cylindrical
Our control modules feature double wire bonds for better connections, greater dependability and longer life despite being subjected to intense vibration and the tough operating environment. Copper slug heat sinks provide better heat dissipation to prevent heat from damaging the module. Our ignition modules will respond to a weak signal from the crankshaft position sensor and begin energizing the coils immediately for better starts in cold weather. High-temperature polymer housing reducing moisture intrusion and minimizes vibration damage for extended life and improved reliability. Our ignition modules are durability tested for 500 thermal cycles ranging from -40C to +125C. With industry leading expertise in electronic ignition, when original equipment fails our products are designed to fix the inherent failure issues. As a global manufacturer of original equipment ignition products, we maintain complete quality control throughout the manufacturing process from componentry to finished product.

Fitment Warning:
This is a Universal/Non Application Specific Product. To install this part, you made need to cut, weld, or make other modifications to your vehicle.

Brand: Standard Ignition

Vehicle

Finish Selecting Your Vehicle

Shop By Brand

Showing Products For 1987 Chevrolet Caprice Ignition Control Module