Shop for Discount Auto Parts, Replacement and Performance Parts and Accessories

2006 Chevrolet HHR Fuel Pump Module Assembly VDO

Part # P311-3C2B2C0 Manu # W0133-1939251 Condition: New

Qty:

In Stock & Ready to Ship

Best Price: $487.87

OEM Product: This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
w/o Fuel Level Sender

Brand: VDO

Vehicle
2006 - Chevrolet HHR

2007 Chevrolet HHR Fuel Pump Module Assembly 4 Cyl 2.2L AutoBest

Part # P311-01A0181 Manu # F2726A Condition: New

Qty:

In Stock & Ready to Ship

Best Price: $144.46

Includes Fuel Pump, Fuel Pressure Regulator, Fuel Tank Pressure Sensor, Sending Unit, Float, Fuel Reservoir, Fuel Strainer and Tank Seal

Brand: AutoBest

Vehicle	Block	Engine	CID	CC
2007 - Chevrolet HHR	L	4 Cyl 2.2L	134	2198

2009 Chevrolet HHR Fuel Pump Module Assembly 4 Cyl 2.4L GMB

Part # P311-4AFC9A4 Manu # 530-2002 Condition: New

Qty:

In Stock & Ready to Ship

Best Price: $296.59

Fuel Pump Module Assembly
Manufactured to meet or exceed OEM specifications.

Brand: GMB

Vehicle	Block	Engine	CID	CC
2009 - Chevrolet HHR	L	4 Cyl 2.4L	145	2384

2006 Chevrolet HHR Fuel Pump Module Assembly 4 Cyl 2.2L US Motor Works - ELECTRIC FUEL PUMP MODULE

Part # P311-1EAAFBD Manu # USEP3715M Condition: New

Qty:

In Stock & Ready to Ship

Best Price: $216.33

ELECTRIC FUEL PUMP MODULE
Product Attributes:
- California Proposition 65: Warning: This Product Contains A Chemical Known To The State Of California To Cause Cancer & Reproductive Harm.
Includes: Tank Seal

Brand: US Motor Works

Vehicle	Submodel	Engine VIN	Block	Engine	CID	CC
2006 - Chevrolet HHR	LT	D	L	4 Cyl 2.2L	134	2198

2011 Chevrolet HHR Fuel Pump Module Assembly 4 Cyl 2.4L Delphi

Part # P311-3FB9FCD Manu # FG1219 Condition: New

This Part Fits the Following OEM/Substitute Numbers: 19179948 , A30427 , DFG1219 , E3806M , M10180 , MU2115 , P76698M , SP6102M

Qty:

In Stock & Ready to Ship

Best Price: $304.42

Fuel Pump Module Assembly
Fuel tank contamination is the leading cause of premature fuel pump failure. To reduce risk of contaminating the replacement pump, Delphi recommends cleaning the fuel tank before installing a new pump. Use of fuel tank cleaning kit FC01 is recommended.
Product Attributes:
- Average Current Draw: 9
- Average Flow Rating: 26
- Fuel Level Sender Assembly Included: Yes
- Fuel Type: Gas
- Internal Or External Strainer: External
- Lock Ring Included: No
- Maximum Pressure: 80.0
- Outlet Outside Diameter: 0.375
- Outlet Quantity: 3
- Pump Type: Electric
- Regulator Included: Yes
- Resistance Ohms Empty: 250.0
- Resistance Ohms Full: 40.0
- Strainer Included: Yes
- System Pressure: 58 Psi
- Terminal Gender: Male
- Terminal Quantity: 4
- Terminal Type: Blade
- Vapor Pressure Sensor: Yes
- Voltage: 12.0
100 years of OE experience, supplier to the world's top automakers, OE Heritage and knowledge built into every aftermarket part, comprehensive portfolio for a wide range of vehicles and model years.

Brand: Delphi

Vehicle	Block	Engine	CID	CC
2011 - Chevrolet HHR	L	4 Cyl 2.4L	145	2384

2010 Chevrolet HHR Fuel Pump Module Assembly 4 Cyl 2.0L Delphi

Part # P311-444D8CA Manu # FG1302 Condition: New

This Part Fits the Following OEM/Substitute Numbers: 19169144 , 19207956 , A30292 , CFG1302 , E3804M , M10152 , MU2116 , P76284M , SP6688M

Qty:

In Stock & Ready to Ship

Best Price: $313.90

Fuel Pump Module Assembly
Fuel tank contamination is the leading cause of premature fuel pump failure. To reduce risk of contaminating the replacement pump, Delphi recommends cleaning the fuel tank before installing a new pump. Use of fuel tank cleaning kit FC01 is recommended.
Product Attributes:
- Average Current Draw: 9
- Average Flow Rating: 30
- Fuel Level Sender Assembly Included: No
- Fuel Type: Gas
- Internal Or External Strainer: Internal
- Lock Ring Included: No
- Maximum Pressure: 94.0
- Outlet Outside Diameter: 0.375
- Outlet Quantity: 3
- Pump Type: Electric
- Regulator Included: Yes
- Strainer Included: Yes
- System Pressure: 58 Psi
- Terminal Gender: Male
- Terminal Quantity: 4
- Terminal Type: Blade
- Vapor Pressure Sensor: Yes
- Voltage: 12.0
100 years of OE experience, supplier to the world's top automakers, OE Heritage and knowledge built into every aftermarket part, comprehensive portfolio for a wide range of vehicles and model years.

Brand: Delphi

Vehicle	Block	Engine	CID	CC
2010 - Chevrolet HHR	L	4 Cyl 2.0L	122	1998

2007 Chevrolet HHR Fuel Pump Module Assembly 4 Cyl 2.2L Delphi

Part # P311-22783DD Manu # FG0974 Condition: New

This Part Fits the Following OEM/Substitute Numbers: 15293417 , 15850486 , 19168521 , 19208960 , 19208967 , 67526 , A30292 , DFG0974 , E3715M , FP22042S , M10015 , MU1540 , P76284M , SP6614M

Qty:

In Stock & Ready to Ship

Best Price: $228.59

Fuel Pump Module Assembly
Fuel tank contamination is the leading cause of premature fuel pump failure. To reduce risk of contaminating the replacement pump, Delphi recommends cleaning the fuel tank before installing a new pump. Use of fuel tank cleaning kit FC01 is recommended.
Product Attributes:
- Average Current Draw: 6
- Average Flow Rating: 26
- Fuel Level Sender Assembly Included: Yes
- Fuel Type: Gas
- Internal Or External Strainer: Internal
- Lock Ring Included: No
- Maximum Pressure: 59.0
- Outlet Outside Diameter: 0.375
- Outlet Quantity: 3
- Pump Type: Electric
- Regulator Included: Yes
- Resistance Ohms Empty: 250.0
- Resistance Ohms Full: 40.0
- Strainer Included: Yes
- System Pressure: 58 Psi
- Terminal Gender: Male
- Terminal Quantity: 4
- Terminal Type: Blade
- Vapor Pressure Sensor: Yes
- Voltage: 12.0
100 years of OE experience, supplier to the world's top automakers, OE Heritage and knowledge built into every aftermarket part, comprehensive portfolio for a wide range of vehicles and model years.

Brand: Delphi

Vehicle	Block	Engine	CID	CC
2007 - Chevrolet HHR	L	4 Cyl 2.2L	134	2198

Fuel Pump Module Assembly Holley

Part # P311-52782C4 Manu # 12-147 Condition: New

Qty:

In Stock & Ready to Ship

Best Price: $777.59

Drop In Fuel Pump Module Assembly
Drop In Fuel Pump Module Assembly; Dual Pumps; Free Flow LPH 450; 8AN Inlet/10 AN Outlet; For Use w/12 Bolt Flange Fuel Cells;
Product Attributes:
- Flange Type: 12 Bolt
- Free Flow GPH: 230
- Fuel Type:
  - E85
  - Gasoline
- Fully Open: 900
- Inlet Size: 8an
- Maximum PSI: 87
- Outlet Size: 10an
- WARNING CA Proposition 65: Yes
- WARNING CA Proposition 65 Message: Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
Features:
- Complete Drop-In Fuel Module Assembly
- Billet Top Flange Housing
- Pump Depth Is Fully Adjustable For Fitment
Updating your racing fuel system to EFI is so simple! Holley is excited to introduce our Holley Fuel Cell EFI Pump Modules. While the name includes EFI, these modules can be used as an upgrade for carbureted systems as well with the proper regulator. The modules were designed to drop in as a direct replacement for your existing 12 bolt flange fuel cell cap assembly. The billet top flange includes an 8AN inlet port, a 10AN outlet port, and a fuel filler cap. The fuel pump depth is fully adjustable from 7.5 in. to 12 in. deep. The EFI modules are available with single and dual 255 LPH and 450 LPH fuel pumps. The module kits include all the hardware to install into your existing fuel cell. All that you need to add is your fuel line.***Assembly fits common RJS, Jaz, Summit, Jegs, RCI, Speedmaster and Speedway fuel cells.***Supports up to 1750 EFI or 2200 Carb HP (@ 60 PSI at 13.5 Volts / 16.9 AMP Draw)

Fitment Warning:
This is a Universal/Non Application Specific Product. To install this part, you made need to cut, weld, or make other modifications to your vehicle.

Brand: Holley

Vehicle

Fuel Pump Module Assembly Holley

Part # P311-13FC370 Manu # 19-380 Condition: New

Qty:

In Stock & Ready to Ship

Best Price: $441.48

Fuel Cell EFI Pump Module Assembly
Fuel Cell EFI Pump Module Assembly; Return Style; 12-Bolt Flange; 340 LPH Drop-In Module; 6AN Inlet/6AN Outlet;
Product Attributes:
- WARNING CA Proposition 65: Yes
- WARNING CA Proposition 65 Message: Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
Features:
- Update Your Fuel Cell To EFI The Easy Way
- Designed To Drop Right In Your Existing 6/12 Bolt Flange
- Pump Depth Fully Adjustable For Fitment Into Most Fuel Cells
Updating your racing fuel system to EFI is so simple! Sniper is introducing their latest Diecast Fuel Cell EFI Pump Modules. The modules were designed to drop in as a direct replacement for your existing 12 bolt flange fuel cell cap assembly. The diecast aluminum top flange includes an 6AN inlet port, a 6AN outlet port, and a fuel filler cap. The fuel pump depth is fully adjustable from 7.5 in. to 12 in. deep. The EFI modules are available with single 340 LPH fuel pumps in both return and returnless system designs. The module kits include all the hardware to install into your existing fuel cell. All that you need to add is your fuel line.***Assembly fits common RJS, Jaz, Summit, Jegs, RCI, Speedmaster and Speedway fuel cells.***Supports up to 700 EFI or 900 Carb HP (HP Rating @ 60 PSI at 13.5 Volts / 10.4 AMP Draw)

Fitment Warning:
This is a Universal/Non Application Specific Product. To install this part, you made need to cut, weld, or make other modifications to your vehicle.

Brand: Holley

Vehicle

Fuel Pump Module Assembly Holley

Part # P311-5E83093 Manu # 12-146 Condition: New

Qty:

In Stock & Ready to Ship

Best Price: $647.15

Fuel Cell EFI Pump Module Assembly
Fuel Cell EFI Pump Module Assembly; 12 Bolt Flange; 450 LPH Drop-In Module; 8AN Inlet/10AN Outlet;
Product Attributes:
- Flange Type: 12 Bolt
- Free Flow GPH: 118
- Fuel Type:
  - E85
  - Gasoline
- Fully Open: 450
- Inlet Size: 8an
- Maximum PSI: 87
- Outlet Size: 10an
- WARNING CA Proposition 65: Yes
- WARNING CA Proposition 65 Message: Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
Features:
- Update Your Fuel Cell To EFI The Easy Way
- Designed To Drop Right In Your Existing 6/12 Bolt Flange
- Billet Top Flange Housing
- Pump Depth Fully Adjustable For Fitment Into Most Fuel Cells
Updating your racing fuel system to EFI is so simple! Holley is excited to introduce our Holley Fuel Cell EFI Pump Modules. While the name includes EFI, these modules can be used as an upgrade for carbureted systems as well with the proper regulator. The modules were designed to drop in as a direct replacement for your existing 12 bolt flange fuel cell cap assembly. The billet top flange includes an 8AN inlet port, a 10AN outlet port, and a fuel filler cap. The fuel pump depth is fully adjustable from 7.5 in. to 12 in. deep. The EFI modules are available with single 255 LPH and 450 LPH fuel pumps. The module kits include all the hardware to install into your existing fuel cell. All that you need to add is your fuel line.***Assembly fits common RJS, Jaz, Summit, Jegs, RCI, Speedmaster and Speedway fuel cells.***Supports up to 875 EFI or 1100 Carb HP (@ 60 PSI at 13.5 Volts / 16.9 AMP Draw)

Fitment Warning:
This is a Universal/Non Application Specific Product. To install this part, you made need to cut, weld, or make other modifications to your vehicle.

Brand: Holley

Vehicle

Fuel Pump Module Assembly Holley

Part # P311-5707EB8 Manu # 19-370 Condition: New

Qty:

In Stock & Ready to Ship

Best Price: $458.36

Fuel Cell EFI Pump Module Assembly
Fuel Cell EFI Pump Module Assembly; Return Style; 6-Bolt Flange; 340 LPH Drop-In Module; 6AN Inlet/6AN Outlet;
Product Attributes:
- WARNING CA Proposition 65: Yes
- WARNING CA Proposition 65 Message: Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
Features:
- Update Your Fuel Cell To EFI The Easy Way
- Designed To Drop Right In Your Existing 6/12 Bolt Flange
- Pump Depth Fully Adjustable For Fitment Into Most Fuel Cells
Updating your racing fuel system to EFI is so simple! Sniper is introducing their latest Diecast Fuel Cell EFI Pump Modules. The modules were designed to drop in as a direct replacement for your existing 6 bolt flange fuel cell cap assembly. The diecast aluminum top flange includes an 6AN inlet port, a 6AN outlet port, and a fuel filler cap. The fuel pump depth is fully adjustable from 7.5 in. to 12 in. deep. The EFI modules are available with single 340 LPH fuel pumps in both return and returnless system designs. The module kits include all the hardware to install into your existing fuel cell. All that you need to add is your fuel line.***Assembly fits common RJS, Jaz, Summit, Jegs, RCI, Speedmaster and Speedway fuel cells.***Supports up to 700 EFI or 900 Carb HP (HP Rating @ 60 PSI at 13.5 Volts / 10.4 AMP Draw)

Fitment Warning:
This is a Universal/Non Application Specific Product. To install this part, you made need to cut, weld, or make other modifications to your vehicle.

Brand: Holley

Vehicle

Fuel Pump Module Assembly Holley

Part # P311-20C92DE Manu # 12-144 Condition: New

Qty:

In Stock & Ready to Ship

Best Price: $619.51

Fuel Cell EFI Pump Module Assembly
Fuel Cell EFI Pump Module Assembly; 12 Bolt Flange; 255 LPH Drop-In Module; 8AN Inlet/10AN Outlet;
Product Attributes:
- Flange Type: 12 Bolt
- Free Flow GPH: 67
- Fuel Type: Gasoline
- Fully Open: 255
- Inlet Size: 8an
- Maximum PSI: 80
- Outlet Size: 10an
- WARNING CA Proposition 65: Yes
- WARNING CA Proposition 65 Message: Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
Features:
- Update Your Fuel Cell To EFI The Easy Way
- Designed To Drop Right In Your Existing 6/12 Bolt Flange
- Billet Top Flange Housing
- Pump Depth Fully Adjustable For Fitment Into Most Fuel Cells
Updating your racing fuel system to EFI is so simple! Holley is excited to introduce our Holley Fuel Cell EFI Pump Modules. While the name includes EFI, these modules can be used as an upgrade for carbureted systems as well with the proper regulator. The modules were designed to drop in as a direct replacement for your existing 12 bolt flange fuel cell cap assembly. The billet top flange includes an 8AN inlet port, a 10AN outlet port, and a fuel filler cap. The fuel pump depth is fully adjustable from 7.5 in. to 12 in. deep. The EFI modules are available with single 255 LPH and 450 LPH fuel pumps. The module kits include all the hardware to install into your existing fuel cell. All that you need to add is your fuel line.***Assembly fits common RJS, Jaz, Summit, Jegs, RCI, Speedmaster and Speedway fuel cells.***Supports up to 550 EFI or 700 Carb HP (HP Rating @ 60 PSI at 13.5 Volts / 10.4 AMP Draw)

Fitment Warning:
This is a Universal/Non Application Specific Product. To install this part, you made need to cut, weld, or make other modifications to your vehicle.

Brand: Holley

Vehicle

Fuel Pump Module Assembly Delphi

Part # P311-1AC5F71 Manu # FG1483 Condition: New

This Part Fits the Following OEM/Substitute Numbers: 3924710C1 , EFG1483

Qty:

In Stock & Ready to Ship

Best Price: $255.27

Fuel Pump Module Assembly
Product Attributes:
- Average Current Draw: 10
- Average Flow Rating: 46
- Fuel Level Sender Assembly Included: Yes
- Fuel Type: Gas
- Internal Or External Strainer: Internal
- Lock Ring Included: No
- Maximum Pressure: 80.0
- Notes: Used On 2012 F64 Navistar
- Outlet Outside Diameter: 0.375
- Outlet Quantity: 2
- Pump Type: Electric
- Regulator Included: Yes
- Resistance Ohms Empty: 180.0
- Resistance Ohms Full: 10.0
- Strainer Included: Yes
- System Pressure: 54 Psi
- Terminal Gender: Male
- Terminal Quantity: 4
- Terminal Type: Blade
- Vapor Pressure Sensor: Yes
- Voltage: 13.0
100 years of OE experience, supplier to the world's top automakers, OE Heritage and knowledge built into every aftermarket part, comprehensive portfolio for a wide range of vehicles and model years.

Fitment Warning:
This is a Universal/Non Application Specific Product. To install this part, you made need to cut, weld, or make other modifications to your vehicle.

Brand: Delphi

Vehicle

Fuel Pump Module Assembly Holley

Part # P311-5698221 Manu # 19-355 Condition: New

Qty:

In Stock & Ready to Ship

Best Price: $667.50

In-Tank Retrofit Fuel Module
In-Tank Retrofit Fuel Module; 340 LPH; Return Style; Install In Any Tank From 7 in. To 12 in. Deep; Includes Filter Socks;
Product Attributes:
- WARNING CA Proposition 65: Yes
- WARNING CA Proposition 65 Message: Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
Features:
- Billet/Anodized/Laser Etched Flanges With 8An ORB Return/Outlet And 6An Orb Vent
- Allows You To Locate The Module Nearly Anywhere In The Tank While Retaining
- The Clamping System Allows You To Rotate The Unit 360 Degrees For Easier Clocking Of The Plumbing And Wiring
- Easy Install Just Drill A 4 in. Hole In The Top Of The Tank Then Use Hand Tools
- E85 Compatible
- The Dual Pump Design Allows The Pumps To Be Ran Together Or The Second Pump Can Be Triggered Additionally
- Units Install In Tanks From 7 To 12 in. Deep
- Filter Socks Included/Hydramats Can Be Purchased Separately
Looking to make a serious step up in the horsepower department? The Holley Dual 3400 LPH EFI Pump Module would be an excellent choice. While the name includes EFI, these modules can be used as an upgrade for carbureted systems as well with the proper regulator.The innovative clamping system allows you to locate the module nearly anywhere in the tank while retaining your factory fuel level sending unit. The clamping system allows you to rotate the unit 360 degrees for easier clocking of the plumbing and wiring locations under your ride.

Fitment Warning:
This is a Universal/Non Application Specific Product. To install this part, you made need to cut, weld, or make other modifications to your vehicle.

Brand: Holley

Vehicle

Fuel Pump Module Assembly Holley

Part # P311-1236054 Manu # 12-132 Condition: New

Qty:

In Stock & Ready to Ship

Best Price: $800.71

In-Tank Retrofit Fuel Module
In-Tank Retrofit Fuel Module; 450 LPH; Install In Any Tank From 7 in. to 12 in. Deep;
Product Attributes:
- Diameter (in.): 4.800 In.
- Fuel Type:
  - E85
  - Gasoline
- Fully Open: 450
- Thread Size: 1/4npt
- WARNING CA Proposition 65: No
Features:
- Easiest Way To Convert Vehicle To An In-Tank EFI Fuel System
- The Low Profile Design For Added Clearance When Needed
- Clamping System Allows You To Locate Module Anywhere In The Tank
- 360 Degree Rotation Clamping Easy Clocking Of Plumbing/Wiring
- Hydramat w/Consistent Fuel Supply/6 Clocking Pin/360 Deg. Adjust
- Black Aluminum For Corrosion Resistance/Long Lasting Good Looks
- 1/4in. Npt Ports For A Wide Variety Of Plumbing Options
Are you interested in an EFI retrofit kit, but just cant get past the complication of the fuel system? Holley is proud to introduce their Universal In-Tank Retrofit Fuel Modules! Available in return and returnless versions, you can rest assured Holley has the solution you need for your EFI fuel pump woes. Now you can convert your factory tank or fuel cell to an in-tank EFI fuel system quickly and easily! And- add the benefits of a Holley Hydramat in the process! The conversion is easily accomplished with basic tools and requires no welding or fabrication. The billet aluminum module design includes a billet pump hanger bracket to control pump vibration while also providing a low profile 5 inch diameter design to fit where space is at a premium. Holleys innovative clamping system and integrated fuel pump makes it easy. Once installed, hook up your fuel lines and your power source/ground and youre off and running! NO hassle! Supports up to 875 EFI or 1100 Carb HP (@ 60 PSI at 13.5 Volts / 16.9 AMP Draw) Of course there are many variables, estimates are based on gasoline. Individual systems will vary based on fuel system design, regulator type, fuel cell location, etc...

Fitment Warning:
This is a Universal/Non Application Specific Product. To install this part, you made need to cut, weld, or make other modifications to your vehicle.

Brand: Holley

Vehicle

Fuel Pump Module Assembly Holley

Part # P311-503382E Manu # 12-156 Condition: New

Qty:

In Stock & Ready to Ship

Best Price: $233.26

In-Tank Retrofit Fuel Module
In-Tank Retrofit Fuel Module; 255 LPH; Returnless Style;
Product Attributes:
- Fully Open: 255
- WARNING CA Proposition 65: Yes
- WARNING CA Proposition 65 Message: Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
Features:
- Returnless Style
- 255 LPH
255 LPH Replacement pump for Retro-Fit and Fuel Cell Modules

Fitment Warning:
This is a Universal/Non Application Specific Product. To install this part, you made need to cut, weld, or make other modifications to your vehicle.

Brand: Holley

Vehicle

Fuel Pump Module Assembly Holley

Part # P311-103AF31 Manu # 19-350 Condition: New

Qty:

In Stock & Ready to Ship

Best Price: $463.60

In-Tank Retrofit Fuel Module
In-Tank Retrofit Fuel Module; 340 LPH; Install In Any Tank From 7 in. to 12 in. Deep;
Product Attributes:
- WARNING CA Proposition 65: Yes
- WARNING CA Proposition 65 Message: Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
Features:
- The Easiest Way To Convert Your Vehicle To An In-tank EFI Fuel System
- Installs In Any Fuel Tank From 7 in. To 12 in. Deep To Fit A Wide Variety Of Applications
- The Low Profile 5 Inch Diameter Design Is Only 1.275 Inches Thick Above The Tank Mounting Surface
- The Innovative Clamping System Allows You To Locate The Module Anywhere In The Tank
- Clamping System Allows You To Rotate The Unit 360 Degrees For Easier Clocking Of The Plumbing
- Die Cast Aluminum Construction For Corrosion Resistance And Long Lasting Good Looks
Holley/MSD is pleased to announce the release of Sniper Diecast Retrofit Fuel Pump Modules, which support up to 700 EFI horsepower or 900 carbureted horsepower and make it easy to affordably upgrade to EFI. Available in return and returnless versions, they convert your factory tank or fuel cell to an in-tank EFI fuel system. They're easy to install with basic hand tools and require no welding or fabrication whatsoever. Sniper Diecast Retrofit Fuel Pump Modules include a diecast pump-hanger bracket to control pump vibration in a low-profile design thats perfect wherever space is at a premium. They fit any fuel-tank depth from 7 to 12 inches and protrude only 1.275-inch above the tank-mounting surface to accommodate numerous applications. You can locate the 5 inch diameter module beside your existing sending unit anywhere in the tank and rotate it a full 360 degrees to work flawlessly with various plumbing and wiring configurations. Once the module is installed, all you need to do is connect your power-source/ground and fuel lines. Supports up to 700 EFI or 900 Carb HP (@ 60 PSI at 13.5 Volts / 16.9 AMP Draw) Of course there are many variables, estimates are based on gasoline. Individual systems will vary based on fuel system design, regulator type, fuel cell location, etc...

Fitment Warning:
This is a Universal/Non Application Specific Product. To install this part, you made need to cut, weld, or make other modifications to your vehicle.

Brand: Holley

Vehicle

Fuel Pump Module Assembly Holley

Part # P311-3FEFDF7 Manu # 12-130 Condition: New

Qty:

In Stock & Ready to Ship

Best Price: $871.37

In-Tank Retrofit Fuel Module
In-Tank Retrofit Fuel Module; 255 LPH; Install In Any Tank From 6.5 in. to 12 in. Deep;
Product Attributes:
- Diameter (in.): 4.800 In.
- Fully Open: 255
- Thread Size: 1/4npt
- WARNING CA Proposition 65: No
Features:
- Easiest Way To Convert Vehicle To An In-Tank EFI Fuel System
- The Low Profile Design For Added Clearance When Needed
- Clamping System Allows You To Locate Module Anywhere In The Tank
- 360 Degree Rotation Clamping Easy Clocking Of Plumbing/Wiring
- Hydramat w/Consistent Fuel Supply/6 Clocking Pin/360 Deg. Adjust
- Black Aluminum For Corrosion Resistance/Long Lasting Good Looks
- 1/4in. Npt Ports For A Wide Variety Of Plumbing Options
Are you interested in an EFI retrofit kit, but just cant get past the complication of the fuel system? Holley is proud to introduce their Universal In-Tank Retrofit Fuel Modules! Available in return and returnless versions, you can rest assured Holley has the solution you need for your EFI fuel pump woes. Now you can convert your factory tank or fuel cell to an in-tank EFI fuel system quickly and easily! And- add the benefits of a Holley Hydramat in the process! The conversion is easily accomplished with basic tools and requires no welding or fabrication. The billet aluminum module design includes a billet pump hanger bracket to control pump vibration while also providing a low profile design to fit where space is at a premium. Holleys innovative clamping system and integrated fuel pump makes it easy. Once installed, hook up your fuel lines and your power source/ground and youre off and running! NO hassle! Supports up to 550 EFI or 700 Carb HP (@ 60 PSI at 13.5 Volts / 10.4 AMP Draw) Of course there are many variables, estimates are based on gasoline. Individual systems will vary based on fuel system design, regulator type, fuel cell location, etc...

Fitment Warning:
This is a Universal/Non Application Specific Product. To install this part, you made need to cut, weld, or make other modifications to your vehicle.

Brand: Holley

Vehicle

Fuel Pump Module Assembly Holley

Part # P311-059CCA6 Manu # 19-360 Condition: New

Qty:

In Stock & Ready to Ship

Best Price: $521.10

In-Tank Retrofit Fuel Module
In-Tank Retrofit Fuel Module; 340 LPH; Returnless; Install In Any Tank From 7 in. to 12 in. Deep;
Product Attributes:
- WARNING CA Proposition 65: Yes
- WARNING CA Proposition 65 Message: Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
Features:
- The Easiest Way To Convert Your Vehicle To An In-tank EFI Fuel System
- Your Factory Fuel Level Sending Unit
- The Low Profile 5 Inch Diameter Design Is Only 1.275 Inches Thick Above The Tank Mounting Surface
- The Innovative Clamping System Allows You To Locate The Module Anywhere In The Tank
- Clamping System Allows You To Rotate The Unit 360 Degrees For Easier Clocking Of The Plumbing
- Die Cast Aluminum Construction For Corrosion Resistance And Long Lasting Good Looks
Holley/MSD is pleased to announce the release of Sniper Diecast Retrofit Fuel Pump Modules, which support up to 700 EFI horsepower or 900 carbureted horsepower and make it easy to affordably upgrade to EFI. Available in return and returnless versions, they convert your factory tank or fuel cell to an in-tank EFI fuel system. They're easy to install with basic hand tools and require no welding or fabrication whatsoever. Sniper Diecast Retrofit Fuel Pump Modules include a diecast pump-hanger bracket to control pump vibration in a low-profile design thats perfect wherever space is at a premium. They fit any fuel-tank depth from 7 to 12 inches and protrude only 1.275-inch above the tank-mounting surface to accommodate numerous applications. You can locate the 5 inch diameter module beside your existing sending unit anywhere in the tank and rotate it a full 360 degrees to work flawlessly with various plumbing and wiring configurations. Once the module is installed, all you need to do is connect your power-source/ground and fuel lines. Supports up to 700 EFI or 900 Carb HP (@ 60 PSI at 13.5 Volts / 16.9 AMP Draw) Of course there are many variables, estimates are based on gasoline. Individual systems will vary based on fuel system design, regulator type, fuel cell location, etc...

Fitment Warning:
This is a Universal/Non Application Specific Product. To install this part, you made need to cut, weld, or make other modifications to your vehicle.

Brand: Holley

Vehicle

Fuel Pump Module Assembly Holley

Part # P311-1C60504 Manu # 12-319 Condition: New

Qty:

In Stock & Ready to Ship

Best Price: $458.00

OEM Style EFI Fuel Tank Modules
OEM Style EFI Fuel Tank Modules; 255 LPH; Includes Fuel Level Sending Unit/Hydra Mat/Internal Fuel Pressure Regulator;
Product Attributes:
- WARNING CA Proposition 65: Yes
- WARNING CA Proposition 65 Message: Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov
Features:
- In-Tank High Pressure 255 lph Unit
- Fuel Pressure Is Internally Regulated To 58 PSI
- A Pre-calibrated Fuel-level Sending Unit 73-10 Ohm
- This Module Also Features A HydraMat Filter
- HydraMart Filter Also Provides Protection From Contaminate
This in-tank fuel pump module is a high-pressure unit that flows 255 liters per hour (LPH) and is capable of supporting EFI (electronic fuel injection) engines producing up to 550 horsepower

Fitment Warning:
This is a Universal/Non Application Specific Product. To install this part, you made need to cut, weld, or make other modifications to your vehicle.

Brand: Holley

Vehicle

Finish Selecting Your Vehicle to Shop For Your Fuel Pump Module

Shop By Brand

Shop By Related Fuel Pump Module Assembly Parts

Shop for Top Selling Genuine Chevrolet Hhr Fuel Pump Modules

Shop Chevrolet Hhr Fuel Pump Modules

Finish Selecting Your Vehicle to Shop For Your Fuel Pump Module

Shop By Brand

Shop By Related Fuel Pump Module Assembly Parts

Shop for Top Selling Genuine Chevrolet Hhr Fuel Pump Modules