Finish Selecting Your Vehicle to Shop For Your Engine Control Module

Choose a Year for your Pontiac Firebird 's Engine Control Module

  • 2002
  • 2001
  • 2000
  • 1999
  • 1995
  • 1994
  • 1992
  • 1991
  • 1990
  • 1989
  • 1988
  • 1987
  • 1986
  • 1985
  • 1984
  • 1983
  • 1982
  • 1981
  • 1980
  • 1979
  • 1978
  • 1977
  • 1976
  • 1975
  • 1974
  • 1973
  • 1972
  • 1971
  • 1970
  • 1969
  • 1968
  • 1967
Show More Years

Shop By Brand

The Following brands are available based on your search.

  • ACDelco
    ACDelco
  • Cardone
    Cardone
  • FAST
    FAST
  • Holley
    Holley
  • Painless Wiring
    Painless Wiring
  • Standard Ignition
    Standard Ignition

Shop By Related Engine Control Module Parts

Shop below for all Engine Control Module related parts for your Pontiac Firebird


Shop for Top Selling Genuine Pontiac Firebird Engine Control Modules

  • We Stock the following top leading brands, including Cardone, ACDelco
  • Constantly Updated Inventory of Pontiac Firebird Replacement Engine Control Module Parts

We also have Engine Control Module parts for other Pontiac models, including Bonneville, Firebird, G6, Grand Am, Grand Prix, Montana.


Cardone
2001 Pontiac Firebird Engine Control Module 8 Cyl 5.7L Cardone - Engine Control Module

P311-48F2EE6    77-0411F  Remanufactured

12200411

Qty:
In Stock & Ready to Ship
$53.10 $115.07
Cardone Engine Control Module
  • with Original Equipment (OE) # 12200411 Vehicle specific Flash programming required ON or OFF the vehicle. Accurate VIN and mileage are required Vehicle specific On-Car Programming must be performed AFTER installation to prevent drivability and starting issues
  • Engine Control Module
  • Product Attributes:
    • FAQs:
      • Chrysler Pcm's Identified With A "v" Suffix Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti Theft System (p.a.t.s) Reset?
      • I Replaced The Pcm In My Gm Vehicle. Do I Need To Reset The Passlock Or Passkey Vehicle Anti Theft System (vats)?
      • No, Not All Ford Vehicles Require A Pats Reset. Check The Pats Chart Found On The Motorcraft Site For Your Application.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Areas That Cause Failures Are: Poor Grounds And Powers, Bad Wiring Harness, Shorted Solenoids/relays.
      • The Replacement Ecm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • The Wrong Ecm May Have Been Installed. Verify The Ford Engineering Id Number, Found On The Ecm/pcm, Crosses To The Correct Cardone Number.
      • What Steps Should I Take To Assure The Original Ecm/pcm Is Causing The Issue?
      • Yes, There's A 10 Minute Procedure Utilizing A Tech 2 Scanner And A Gm Terminal Subscription. There Is Also A 30 Minute Manual Procedure That Can Be Done Without A Scanner. Refer To An Oe Approved Service Manual For Either Option.
    • Features and Benefits:
      • As A Remanufactured Original Equipment Part, This Unit Guarantees A Perfect Vehicle Fit.
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Our Remanufacturing Process Is Earth-friendly, As It Reduces The Energy And Raw Material Needed To Make A New Part By 80%.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated Computer Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design weaknesses. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant, and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back to peak performance.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
2001 - Pontiac Firebird V 8 Cyl 5.7L 350 -
Cardone
1991 Pontiac Firebird Engine Control Module 8 Cyl 5.0L Cardone - Engine Control Module

P311-5A2652F    77-7730  Remanufactured

Qty:
In Stock & Ready to Ship
$32.40 $108.75
Cardone Engine Control Module
  • with Original Equipment (OE) # 1227730, 16196344, 16198262 The PROM(s)/CALPACK must be transferred from the original module to the replacement module Additional relearns (theft, crankshaft, idle, etc) may be required
  • Engine Control Module
  • Product Attributes:
    • FAQs:
      • Chrysler Pcm's Identified With A "v" Suffix Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti Theft System (p.a.t.s) Reset?
      • I Replaced The Pcm In My Gm Vehicle. Do I Need To Reset The Passlock Or Passkey Vehicle Anti Theft System (vats)?
      • No, Not All Ford Vehicles Require A Pats Reset. Check The Pats Chart Found On The Motorcraft Site For Your Application.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Areas That Cause Failures Are: Poor Grounds And Powers, Bad Wiring Harness, Shorted Solenoids/relays.
      • The Replacement Ecm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • The Wrong Ecm May Have Been Installed. Verify The Ford Engineering Id Number, Found On The Ecm/pcm, Crosses To The Correct Cardone Number.
      • What Steps Should I Take To Assure The Original Ecm/pcm Is Causing The Issue?
      • Yes, There's A 10 Minute Procedure Utilizing A Tech 2 Scanner And A Gm Terminal Subscription. There Is Also A 30 Minute Manual Procedure That Can Be Done Without A Scanner. Refer To An Oe Approved Service Manual For Either Option.
    • Features and Benefits:
      • As A Remanufactured Original Equipment Part, This Unit Guarantees A Perfect Vehicle Fit.
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Our Remanufacturing Process Is Earth-friendly, As It Reduces The Energy And Raw Material Needed To Make A New Part By 80%.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated Computer Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design weaknesses. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant, and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back to peak performance.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
1991 - Pontiac Firebird V 8 Cyl 5.0L 305 -
Cardone
1992 Pontiac Firebird Engine Control Module 6 Cyl 3.1L Cardone - Engine Control Module

P311-5A2652F    77-7730  Remanufactured

1227730 , 16196344 , 16198262 , 88999196

Qty:
In Stock & Ready to Ship
$32.40 $108.75
Cardone Engine Control Module
  • The PROM(s)/CALPACK must be transferred from the original module to the replacement module Additional relearns (theft, crankshaft, idle, etc) may be required
  • Engine Control Module
  • Product Attributes:
    • FAQs:
      • Chrysler Pcm's Identified With A "v" Suffix Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti Theft System (p.a.t.s) Reset?
      • I Replaced The Pcm In My Gm Vehicle. Do I Need To Reset The Passlock Or Passkey Vehicle Anti Theft System (vats)?
      • No, Not All Ford Vehicles Require A Pats Reset. Check The Pats Chart Found On The Motorcraft Site For Your Application.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Areas That Cause Failures Are: Poor Grounds And Powers, Bad Wiring Harness, Shorted Solenoids/relays.
      • The Replacement Ecm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • The Wrong Ecm May Have Been Installed. Verify The Ford Engineering Id Number, Found On The Ecm/pcm, Crosses To The Correct Cardone Number.
      • What Steps Should I Take To Assure The Original Ecm/pcm Is Causing The Issue?
      • Yes, There's A 10 Minute Procedure Utilizing A Tech 2 Scanner And A Gm Terminal Subscription. There Is Also A 30 Minute Manual Procedure That Can Be Done Without A Scanner. Refer To An Oe Approved Service Manual For Either Option.
    • Features and Benefits:
      • As A Remanufactured Original Equipment Part, This Unit Guarantees A Perfect Vehicle Fit.
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Our Remanufacturing Process Is Earth-friendly, As It Reduces The Energy And Raw Material Needed To Make A New Part By 80%.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated Computer Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design weaknesses. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant, and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back to peak performance.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
1992 - Pontiac Firebird V 6 Cyl 3.1L 189 -
Cardone
2000 Pontiac Firebird Engine Control Module 6 Cyl 3.8L Cardone - Engine Control Module

P311-25B5AD0    77-0717F  Remanufactured

9380717

Qty:
In Stock & Ready to Ship
$38.70 $124.42
Cardone Engine Control Module
  • Vehicle specific Flash programming required ON or OFF the vehicle. Accurate VIN and mileage are required Vehicle specific On-Car Programming must be performed AFTER installation to prevent drivability and starting issues
  • Engine Control Module
  • Product Attributes:
    • FAQs:
      • Chrysler Pcm's Identified With A "v" Suffix Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti Theft System (p.a.t.s) Reset?
      • I Replaced The Pcm In My Gm Vehicle. Do I Need To Reset The Passlock Or Passkey Vehicle Anti Theft System (vats)?
      • No, Not All Ford Vehicles Require A Pats Reset. Check The Pats Chart Found On The Motorcraft Site For Your Application.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Areas That Cause Failures Are: Poor Grounds And Powers, Bad Wiring Harness, Shorted Solenoids/relays.
      • The Replacement Ecm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • The Wrong Ecm May Have Been Installed. Verify The Ford Engineering Id Number, Found On The Ecm/pcm, Crosses To The Correct Cardone Number.
      • What Steps Should I Take To Assure The Original Ecm/pcm Is Causing The Issue?
      • Yes, There's A 10 Minute Procedure Utilizing A Tech 2 Scanner And A Gm Terminal Subscription. There Is Also A 30 Minute Manual Procedure That Can Be Done Without A Scanner. Refer To An Oe Approved Service Manual For Either Option.
    • Features and Benefits:
      • As A Remanufactured Original Equipment Part, This Unit Guarantees A Perfect Vehicle Fit.
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Our Remanufacturing Process Is Earth-friendly, As It Reduces The Energy And Raw Material Needed To Make A New Part By 80%.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated Computer Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design weaknesses. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant, and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back to peak performance.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
2000 - Pontiac Firebird V 6 Cyl 3.8L 231 3800
Cardone
2001 Pontiac Firebird Engine Control Module 6 Cyl 3.8L Cardone - Engine Control Module

P311-25B5AD0    77-0717F  Remanufactured

Qty:
In Stock & Ready to Ship
$38.70 $124.42
Cardone Engine Control Module
  • with Original Equipment (OE) # 16268183 Vehicle specific Flash programming required ON or OFF the vehicle. Accurate VIN and mileage are required Vehicle specific On-Car Programming must be performed AFTER installation to prevent drivability and starting issues
  • Engine Control Module
  • Product Attributes:
    • FAQs:
      • Chrysler Pcm's Identified With A "v" Suffix Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti Theft System (p.a.t.s) Reset?
      • I Replaced The Pcm In My Gm Vehicle. Do I Need To Reset The Passlock Or Passkey Vehicle Anti Theft System (vats)?
      • No, Not All Ford Vehicles Require A Pats Reset. Check The Pats Chart Found On The Motorcraft Site For Your Application.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Areas That Cause Failures Are: Poor Grounds And Powers, Bad Wiring Harness, Shorted Solenoids/relays.
      • The Replacement Ecm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • The Wrong Ecm May Have Been Installed. Verify The Ford Engineering Id Number, Found On The Ecm/pcm, Crosses To The Correct Cardone Number.
      • What Steps Should I Take To Assure The Original Ecm/pcm Is Causing The Issue?
      • Yes, There's A 10 Minute Procedure Utilizing A Tech 2 Scanner And A Gm Terminal Subscription. There Is Also A 30 Minute Manual Procedure That Can Be Done Without A Scanner. Refer To An Oe Approved Service Manual For Either Option.
    • Features and Benefits:
      • As A Remanufactured Original Equipment Part, This Unit Guarantees A Perfect Vehicle Fit.
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Our Remanufacturing Process Is Earth-friendly, As It Reduces The Energy And Raw Material Needed To Make A New Part By 80%.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated Computer Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design weaknesses. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant, and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back to peak performance.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
2001 - Pontiac Firebird V 6 Cyl 3.8L 231 3800
Cardone
1989 Pontiac Firebird Engine Control Module 6 Cyl 3.8L Cardone - Engine Control Module

P311-55944CC    77-7148  Remanufactured

1227148

Qty:
In Stock & Ready to Ship
$19.80 $106.49
Cardone Engine Control Module
  • with Original Equipment (OE) # 1227148 The PROM(s)/CALPACK must be transferred from the original module to the replacement module Additional relearns (theft, crankshaft, idle, etc) may be required
  • Engine Control Module
  • Product Attributes:
    • FAQs:
      • Chrysler Pcm's Identified With A "v" Suffix Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti Theft System (p.a.t.s) Reset?
      • I Replaced The Pcm In My Gm Vehicle. Do I Need To Reset The Passlock Or Passkey Vehicle Anti Theft System (vats)?
      • No, Not All Ford Vehicles Require A Pats Reset. Check The Pats Chart Found On The Motorcraft Site For Your Application.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Areas That Cause Failures Are: Poor Grounds And Powers, Bad Wiring Harness, Shorted Solenoids/relays.
      • The Replacement Ecm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • The Wrong Ecm May Have Been Installed. Verify The Ford Engineering Id Number, Found On The Ecm/pcm, Crosses To The Correct Cardone Number.
      • What Steps Should I Take To Assure The Original Ecm/pcm Is Causing The Issue?
      • Yes, There's A 10 Minute Procedure Utilizing A Tech 2 Scanner And A Gm Terminal Subscription. There Is Also A 30 Minute Manual Procedure That Can Be Done Without A Scanner. Refer To An Oe Approved Service Manual For Either Option.
    • Features and Benefits:
      • As A Remanufactured Original Equipment Part, This Unit Guarantees A Perfect Vehicle Fit.
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Our Remanufacturing Process Is Earth-friendly, As It Reduces The Energy And Raw Material Needed To Make A New Part By 80%.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated Computer Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design weaknesses. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant, and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back to peak performance.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
1989 - Pontiac Firebird V 6 Cyl 3.8L 231 3800
Cardone
1984 Pontiac Firebird Engine Control Module 4 Cyl 2.5L Cardone - Engine Control Module

P311-124A192    77-6156  Remanufactured

1226156 , 88999112

Qty:
In Stock & Ready to Ship
$120.59
Cardone Engine Control Module
  • The PROM(s)/CALPACK must be transferred from the original module to the replacement module Additional relearns (theft, crankshaft, idle, etc) may be required
  • Engine Control Module
  • Product Attributes:
    • FAQs:
      • Chrysler Pcm's Identified With A "v" Suffix Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti Theft System (p.a.t.s) Reset?
      • I Replaced The Pcm In My Gm Vehicle. Do I Need To Reset The Passlock Or Passkey Vehicle Anti Theft System (vats)?
      • No, Not All Ford Vehicles Require A Pats Reset. Check The Pats Chart Found On The Motorcraft Site For Your Application.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Areas That Cause Failures Are: Poor Grounds And Powers, Bad Wiring Harness, Shorted Solenoids/relays.
      • The Replacement Ecm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • The Wrong Ecm May Have Been Installed. Verify The Ford Engineering Id Number, Found On The Ecm/pcm, Crosses To The Correct Cardone Number.
      • What Steps Should I Take To Assure The Original Ecm/pcm Is Causing The Issue?
      • Yes, There's A 10 Minute Procedure Utilizing A Tech 2 Scanner And A Gm Terminal Subscription. There Is Also A 30 Minute Manual Procedure That Can Be Done Without A Scanner. Refer To An Oe Approved Service Manual For Either Option.
    • Features and Benefits:
      • As A Remanufactured Original Equipment Part, This Unit Guarantees A Perfect Vehicle Fit.
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Our Remanufacturing Process Is Earth-friendly, As It Reduces The Energy And Raw Material Needed To Make A New Part By 80%.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated Computer Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design weaknesses. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant, and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back to peak performance.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
1984 - Pontiac Firebird L 4 Cyl 2.5L 151 2474
Cardone
1989 Pontiac Firebird Engine Control Module 8 Cyl 5.0L Cardone - Engine Control Module

P311-59C4BC5    77-8746  Remanufactured

1228746

Qty:
In Stock & Ready to Ship
$33.30 $97.33
Cardone Engine Control Module
  • with Original Equipment (OE) # 1228746 The PROM(s)/CALPACK must be transferred from the original module to the replacement module Additional relearns (theft, crankshaft, idle, etc) may be required
  • Engine Control Module
  • Product Attributes:
    • FAQs:
      • Chrysler Pcm's Identified With A "v" Suffix Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti Theft System (p.a.t.s) Reset?
      • I Replaced The Pcm In My Gm Vehicle. Do I Need To Reset The Passlock Or Passkey Vehicle Anti Theft System (vats)?
      • No, Not All Ford Vehicles Require A Pats Reset. Check The Pats Chart Found On The Motorcraft Site For Your Application.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Areas That Cause Failures Are: Poor Grounds And Powers, Bad Wiring Harness, Shorted Solenoids/relays.
      • The Replacement Ecm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • The Wrong Ecm May Have Been Installed. Verify The Ford Engineering Id Number, Found On The Ecm/pcm, Crosses To The Correct Cardone Number.
      • What Steps Should I Take To Assure The Original Ecm/pcm Is Causing The Issue?
      • Yes, There's A 10 Minute Procedure Utilizing A Tech 2 Scanner And A Gm Terminal Subscription. There Is Also A 30 Minute Manual Procedure That Can Be Done Without A Scanner. Refer To An Oe Approved Service Manual For Either Option.
    • Features and Benefits:
      • As A Remanufactured Original Equipment Part, This Unit Guarantees A Perfect Vehicle Fit.
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Our Remanufacturing Process Is Earth-friendly, As It Reduces The Energy And Raw Material Needed To Make A New Part By 80%.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated Computer Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design weaknesses. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant, and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back to peak performance.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
1989 - Pontiac Firebird V 8 Cyl 5.0L 305 -
Cardone
1981 Pontiac Firebird Engine Control Module 8 Cyl 5.0L Cardone - Engine Control Module

P311-4A3CF7C    77-4810  Remanufactured

1224810

Qty:
In Stock & Ready to Ship
$129.56
Cardone Engine Control Module
  • with Original Equipment (OE) # 1224810 The PROM(s)/CALPACK must be transferred from the original module to the replacement module Additional relearns (theft, crankshaft, idle, etc) may be required
  • Engine Control Module
  • Product Attributes:
    • FAQs:
      • Chrysler Pcm's Identified With A "v" Suffix Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti Theft System (p.a.t.s) Reset?
      • I Replaced The Pcm In My Gm Vehicle. Do I Need To Reset The Passlock Or Passkey Vehicle Anti Theft System (vats)?
      • No, Not All Ford Vehicles Require A Pats Reset. Check The Pats Chart Found On The Motorcraft Site For Your Application.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Areas That Cause Failures Are: Poor Grounds And Powers, Bad Wiring Harness, Shorted Solenoids/relays.
      • The Replacement Ecm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • The Wrong Ecm May Have Been Installed. Verify The Ford Engineering Id Number, Found On The Ecm/pcm, Crosses To The Correct Cardone Number.
      • What Steps Should I Take To Assure The Original Ecm/pcm Is Causing The Issue?
      • Yes, There's A 10 Minute Procedure Utilizing A Tech 2 Scanner And A Gm Terminal Subscription. There Is Also A 30 Minute Manual Procedure That Can Be Done Without A Scanner. Refer To An Oe Approved Service Manual For Either Option.
    • Features and Benefits:
      • As A Remanufactured Original Equipment Part, This Unit Guarantees A Perfect Vehicle Fit.
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Our Remanufacturing Process Is Earth-friendly, As It Reduces The Energy And Raw Material Needed To Make A New Part By 80%.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated Computer Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design weaknesses. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant, and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back to peak performance.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
1981 - Pontiac Firebird V 8 Cyl 5.0L 305 -
Cardone
1980 Pontiac Firebird Engine Control Module 6 Cyl 3.8L Cardone - Engine Control Module

P311-4A3CF7C    77-4810  Remanufactured

Qty:
In Stock & Ready to Ship
$129.56
Cardone Engine Control Module
  • with Federal Emissions System with Original Equipment (OE) # 1224810 The PROM(s)/CALPACK must be transferred from the original module to the replacement module Additional relearns (theft, crankshaft, idle, etc) may be required
  • Engine Control Module
  • Product Attributes:
    • FAQs:
      • Chrysler Pcm's Identified With A "v" Suffix Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti Theft System (p.a.t.s) Reset?
      • I Replaced The Pcm In My Gm Vehicle. Do I Need To Reset The Passlock Or Passkey Vehicle Anti Theft System (vats)?
      • No, Not All Ford Vehicles Require A Pats Reset. Check The Pats Chart Found On The Motorcraft Site For Your Application.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Areas That Cause Failures Are: Poor Grounds And Powers, Bad Wiring Harness, Shorted Solenoids/relays.
      • The Replacement Ecm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • The Wrong Ecm May Have Been Installed. Verify The Ford Engineering Id Number, Found On The Ecm/pcm, Crosses To The Correct Cardone Number.
      • What Steps Should I Take To Assure The Original Ecm/pcm Is Causing The Issue?
      • Yes, There's A 10 Minute Procedure Utilizing A Tech 2 Scanner And A Gm Terminal Subscription. There Is Also A 30 Minute Manual Procedure That Can Be Done Without A Scanner. Refer To An Oe Approved Service Manual For Either Option.
    • Features and Benefits:
      • As A Remanufactured Original Equipment Part, This Unit Guarantees A Perfect Vehicle Fit.
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Our Remanufacturing Process Is Earth-friendly, As It Reduces The Energy And Raw Material Needed To Make A New Part By 80%.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated Computer Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design weaknesses. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant, and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back to peak performance.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
1980 - Pontiac Firebird V 6 Cyl 3.8L 231 3800
Cardone
1985 Pontiac Firebird Engine Control Module 4 Cyl 2.5L Cardone - Engine Control Module

P311-3CA57C3    77-6864  Remanufactured

1226864

Qty:
In Stock & Ready to Ship
$122.07
Cardone Engine Control Module
  • The PROM(s)/CALPACK must be transferred from the original module to the replacement module Additional relearns (theft, crankshaft, idle, etc) may be required
  • Engine Control Module
  • Product Attributes:
    • FAQs:
      • Chrysler Pcm's Identified With A "v" Suffix Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti Theft System (p.a.t.s) Reset?
      • I Replaced The Pcm In My Gm Vehicle. Do I Need To Reset The Passlock Or Passkey Vehicle Anti Theft System (vats)?
      • No, Not All Ford Vehicles Require A Pats Reset. Check The Pats Chart Found On The Motorcraft Site For Your Application.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Areas That Cause Failures Are: Poor Grounds And Powers, Bad Wiring Harness, Shorted Solenoids/relays.
      • The Replacement Ecm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • The Wrong Ecm May Have Been Installed. Verify The Ford Engineering Id Number, Found On The Ecm/pcm, Crosses To The Correct Cardone Number.
      • What Steps Should I Take To Assure The Original Ecm/pcm Is Causing The Issue?
      • Yes, There's A 10 Minute Procedure Utilizing A Tech 2 Scanner And A Gm Terminal Subscription. There Is Also A 30 Minute Manual Procedure That Can Be Done Without A Scanner. Refer To An Oe Approved Service Manual For Either Option.
    • Features and Benefits:
      • As A Remanufactured Original Equipment Part, This Unit Guarantees A Perfect Vehicle Fit.
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Our Remanufacturing Process Is Earth-friendly, As It Reduces The Energy And Raw Material Needed To Make A New Part By 80%.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated Computer Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design weaknesses. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant, and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back to peak performance.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
1985 - Pontiac Firebird L 4 Cyl 2.5L 151 2474
Cardone
1985 Pontiac Firebird Engine Control Module 6 Cyl 2.8L Cardone - Engine Control Module

P311-36D48A3    77-6870  Remanufactured

1226870

Qty:
In Stock & Ready to Ship
$19.80 $103.90
Cardone Engine Control Module
  • The PROM(s)/CALPACK must be transferred from the original module to the replacement module Additional relearns (theft, crankshaft, idle, etc) may be required
  • Engine Control Module
  • Product Attributes:
    • FAQs:
      • Chrysler Pcm's Identified With A "v" Suffix Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti Theft System (p.a.t.s) Reset?
      • I Replaced The Pcm In My Gm Vehicle. Do I Need To Reset The Passlock Or Passkey Vehicle Anti Theft System (vats)?
      • No, Not All Ford Vehicles Require A Pats Reset. Check The Pats Chart Found On The Motorcraft Site For Your Application.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Areas That Cause Failures Are: Poor Grounds And Powers, Bad Wiring Harness, Shorted Solenoids/relays.
      • The Replacement Ecm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • The Wrong Ecm May Have Been Installed. Verify The Ford Engineering Id Number, Found On The Ecm/pcm, Crosses To The Correct Cardone Number.
      • What Steps Should I Take To Assure The Original Ecm/pcm Is Causing The Issue?
      • Yes, There's A 10 Minute Procedure Utilizing A Tech 2 Scanner And A Gm Terminal Subscription. There Is Also A 30 Minute Manual Procedure That Can Be Done Without A Scanner. Refer To An Oe Approved Service Manual For Either Option.
    • Features and Benefits:
      • As A Remanufactured Original Equipment Part, This Unit Guarantees A Perfect Vehicle Fit.
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Our Remanufacturing Process Is Earth-friendly, As It Reduces The Energy And Raw Material Needed To Make A New Part By 80%.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated Computer Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design weaknesses. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant, and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back to peak performance.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
1985 - Pontiac Firebird V 6 Cyl 2.8L 173 -
Cardone
1986 Pontiac Firebird Engine Control Module 8 Cyl 5.0L Cardone - Engine Control Module

P311-32CAB97    77-7169  Remanufactured

1227169

Qty:
In Stock & Ready to Ship
$110.75
Cardone Engine Control Module
  • The PROM(s)/CALPACK must be transferred from the original module to the replacement module Additional relearns (theft, crankshaft, idle, etc) may be required
  • Engine Control Module
  • Product Attributes:
    • FAQs:
      • Chrysler Pcm's Identified With A "v" Suffix Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti Theft System (p.a.t.s) Reset?
      • I Replaced The Pcm In My Gm Vehicle. Do I Need To Reset The Passlock Or Passkey Vehicle Anti Theft System (vats)?
      • No, Not All Ford Vehicles Require A Pats Reset. Check The Pats Chart Found On The Motorcraft Site For Your Application.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Areas That Cause Failures Are: Poor Grounds And Powers, Bad Wiring Harness, Shorted Solenoids/relays.
      • The Replacement Ecm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • The Wrong Ecm May Have Been Installed. Verify The Ford Engineering Id Number, Found On The Ecm/pcm, Crosses To The Correct Cardone Number.
      • What Steps Should I Take To Assure The Original Ecm/pcm Is Causing The Issue?
      • Yes, There's A 10 Minute Procedure Utilizing A Tech 2 Scanner And A Gm Terminal Subscription. There Is Also A 30 Minute Manual Procedure That Can Be Done Without A Scanner. Refer To An Oe Approved Service Manual For Either Option.
    • Features and Benefits:
      • As A Remanufactured Original Equipment Part, This Unit Guarantees A Perfect Vehicle Fit.
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Our Remanufacturing Process Is Earth-friendly, As It Reduces The Energy And Raw Material Needed To Make A New Part By 80%.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated Computer Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design weaknesses. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant, and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back to peak performance.
Brand: Cardone
Additional Fitment Information:
Vehicle Fuel Delivery Type Block Engine CID CC
1986 - Pontiac Firebird CARB V 8 Cyl 5.0L 305 -
Cardone
1982 Pontiac Firebird Engine Control Module 6 Cyl 2.8L Cardone - Engine Control Module

P311-5C26078    77-5500  Remanufactured

1225500

Qty:
In Stock & Ready to Ship
$106.19
Cardone Engine Control Module
  • with Original Equipment (OE) # 1225500 The PROM(s)/CALPACK must be transferred from the original module to the replacement module Additional relearns (theft, crankshaft, idle, etc) may be required
  • Engine Control Module
  • Product Attributes:
    • FAQs:
      • Chrysler Pcm's Identified With A "v" Suffix Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti Theft System (p.a.t.s) Reset?
      • I Replaced The Pcm In My Gm Vehicle. Do I Need To Reset The Passlock Or Passkey Vehicle Anti Theft System (vats)?
      • No, Not All Ford Vehicles Require A Pats Reset. Check The Pats Chart Found On The Motorcraft Site For Your Application.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Areas That Cause Failures Are: Poor Grounds And Powers, Bad Wiring Harness, Shorted Solenoids/relays.
      • The Replacement Ecm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • The Wrong Ecm May Have Been Installed. Verify The Ford Engineering Id Number, Found On The Ecm/pcm, Crosses To The Correct Cardone Number.
      • What Steps Should I Take To Assure The Original Ecm/pcm Is Causing The Issue?
      • Yes, There's A 10 Minute Procedure Utilizing A Tech 2 Scanner And A Gm Terminal Subscription. There Is Also A 30 Minute Manual Procedure That Can Be Done Without A Scanner. Refer To An Oe Approved Service Manual For Either Option.
    • Features and Benefits:
      • As A Remanufactured Original Equipment Part, This Unit Guarantees A Perfect Vehicle Fit.
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Our Remanufacturing Process Is Earth-friendly, As It Reduces The Energy And Raw Material Needed To Make A New Part By 80%.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated Computer Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design weaknesses. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant, and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back to peak performance.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
1982 - Pontiac Firebird V 6 Cyl 2.8L 173 -
ACDelco
Qty:
In Stock & Ready to Ship
$135.00 $162.55
ACDelco Engine Control Module
  • Remanufactured; INCLUDES UNPROGRAMMED EPROM) (CODE BDTF, BHZU, BJHJ, BJHK, BJHL, BJHM, BJHN, BJHP, BJHR, BJHS, BKNA, BJUC, BKNJ, BMFN; REQUIRES REPROGRAMMING
Brand: ACDelco
Additional Fitment Information:
Vehicle Engine VIN Block Engine
1995 - Pontiac Firebird P V 8 Cyl 5.7L
ACDelco
Qty:
In Stock & Ready to Ship
$22.50 $102.57
ACDelco Engine Control Module
  • Remanufactured; Units are pre-programmed at the factory.
Brand: ACDelco
Additional Fitment Information:
Vehicle Engine
1986 - Pontiac Firebird 4 Cyl 2.5L
Cardone
1983 Pontiac Firebird Engine Control Module 4 Cyl 2.5L Cardone - Engine Control Module

P311-183204C    77-6100  Remanufactured

1226100

Qty:
In Stock & Ready to Ship
$15.30 $117.21
Cardone Engine Control Module
  • The PROM(s)/CALPACK must be transferred from the original module to the replacement module Additional relearns (theft, crankshaft, idle, etc) may be required
  • Engine Control Module
  • Product Attributes:
    • FAQs:
      • Chrysler Pcm's Identified With A "v" Suffix Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti Theft System (p.a.t.s) Reset?
      • I Replaced The Pcm In My Gm Vehicle. Do I Need To Reset The Passlock Or Passkey Vehicle Anti Theft System (vats)?
      • No, Not All Ford Vehicles Require A Pats Reset. Check The Pats Chart Found On The Motorcraft Site For Your Application.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Areas That Cause Failures Are: Poor Grounds And Powers, Bad Wiring Harness, Shorted Solenoids/relays.
      • The Replacement Ecm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • The Wrong Ecm May Have Been Installed. Verify The Ford Engineering Id Number, Found On The Ecm/pcm, Crosses To The Correct Cardone Number.
      • What Steps Should I Take To Assure The Original Ecm/pcm Is Causing The Issue?
      • Yes, There's A 10 Minute Procedure Utilizing A Tech 2 Scanner And A Gm Terminal Subscription. There Is Also A 30 Minute Manual Procedure That Can Be Done Without A Scanner. Refer To An Oe Approved Service Manual For Either Option.
    • Features and Benefits:
      • As A Remanufactured Original Equipment Part, This Unit Guarantees A Perfect Vehicle Fit.
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Our Remanufacturing Process Is Earth-friendly, As It Reduces The Energy And Raw Material Needed To Make A New Part By 80%.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated Computer Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design weaknesses. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant, and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back to peak performance.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
1983 - Pontiac Firebird L 4 Cyl 2.5L 151 2474
ACDelco
Qty:
In Stock & Ready to Ship
$45.00 $120.81
ACDelco Engine Control Module
  • Remanufactured; Remanufactured-NOT FOR SALE WHERE IMPORTS ARE RESTRICTED; CODE 1226870
Brand: ACDelco
Additional Fitment Information:
Vehicle Engine Designation Engine VIN Block Engine
1988 - Pontiac Firebird LB9 F V 8 Cyl 5.0L
Cardone
1987 Pontiac Firebird Engine Control Module 8 Cyl 5.0L Cardone - Engine Control Module

P311-07FEEC5    77-8079  Remanufactured

1228079

Qty:
In Stock & Ready to Ship
$15.30 $105.00
Cardone Engine Control Module
  • The PROM(s)/CALPACK must be transferred from the original module to the replacement module Additional relearns (theft, crankshaft, idle, etc) may be required
  • Engine Control Module
  • Product Attributes:
    • FAQs:
      • Chrysler Pcm's Identified With A "v" Suffix Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti Theft System (p.a.t.s) Reset?
      • I Replaced The Pcm In My Gm Vehicle. Do I Need To Reset The Passlock Or Passkey Vehicle Anti Theft System (vats)?
      • No, Not All Ford Vehicles Require A Pats Reset. Check The Pats Chart Found On The Motorcraft Site For Your Application.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Areas That Cause Failures Are: Poor Grounds And Powers, Bad Wiring Harness, Shorted Solenoids/relays.
      • The Replacement Ecm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • The Wrong Ecm May Have Been Installed. Verify The Ford Engineering Id Number, Found On The Ecm/pcm, Crosses To The Correct Cardone Number.
      • What Steps Should I Take To Assure The Original Ecm/pcm Is Causing The Issue?
      • Yes, There's A 10 Minute Procedure Utilizing A Tech 2 Scanner And A Gm Terminal Subscription. There Is Also A 30 Minute Manual Procedure That Can Be Done Without A Scanner. Refer To An Oe Approved Service Manual For Either Option.
    • Features and Benefits:
      • As A Remanufactured Original Equipment Part, This Unit Guarantees A Perfect Vehicle Fit.
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Our Remanufacturing Process Is Earth-friendly, As It Reduces The Energy And Raw Material Needed To Make A New Part By 80%.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated Computer Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design weaknesses. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant, and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back to peak performance.
Brand: Cardone
Additional Fitment Information:
Vehicle Fuel Delivery Type Block Engine CID CC
1987 - Pontiac Firebird CARB V 8 Cyl 5.0L 305 -
Cardone
1988 Pontiac Firebird Engine Control Module 6 Cyl 2.8L Cardone - Engine Control Module

P311-1F43441    77-7302  Remanufactured

1227302

Qty:
In Stock & Ready to Ship
$97.33
Cardone Engine Control Module
  • The PROM(s)/CALPACK must be transferred from the original module to the replacement module Additional relearns (theft, crankshaft, idle, etc) may be required
  • Engine Control Module
  • Product Attributes:
    • FAQs:
      • Chrysler Pcm's Identified With A "v" Suffix Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti Theft System (p.a.t.s) Reset?
      • I Replaced The Pcm In My Gm Vehicle. Do I Need To Reset The Passlock Or Passkey Vehicle Anti Theft System (vats)?
      • No, Not All Ford Vehicles Require A Pats Reset. Check The Pats Chart Found On The Motorcraft Site For Your Application.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Areas That Cause Failures Are: Poor Grounds And Powers, Bad Wiring Harness, Shorted Solenoids/relays.
      • The Replacement Ecm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • The Wrong Ecm May Have Been Installed. Verify The Ford Engineering Id Number, Found On The Ecm/pcm, Crosses To The Correct Cardone Number.
      • What Steps Should I Take To Assure The Original Ecm/pcm Is Causing The Issue?
      • Yes, There's A 10 Minute Procedure Utilizing A Tech 2 Scanner And A Gm Terminal Subscription. There Is Also A 30 Minute Manual Procedure That Can Be Done Without A Scanner. Refer To An Oe Approved Service Manual For Either Option.
    • Features and Benefits:
      • As A Remanufactured Original Equipment Part, This Unit Guarantees A Perfect Vehicle Fit.
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Our Remanufacturing Process Is Earth-friendly, As It Reduces The Energy And Raw Material Needed To Make A New Part By 80%.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated Computer Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design weaknesses. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant, and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back to peak performance.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
1988 - Pontiac Firebird V 6 Cyl 2.8L 173 -