802.589.0911 Live Chat With Us

Finish Selecting Your Vehicle to Shop For Your Engine Control Module

Choose a Year for your Isuzu 's Engine Control Module

  • 2007
  • 2006
  • 2004
  • 2003
  • 1998
  • 1997
  • 1996
  • 1994
  • 1993
  • 1991
  • 1988

Shop By Brand

The Following brands are available based on your search.

  • Cardone
    Cardone

Best Selling Genuine Isuzu Engine Control Modules

  • We Stock the following top leading brands, including Cardone
  • Constantly Updated Inventory of Isuzu Replacement Engine Control Module Parts

We stock Engine Control Module parts for most Isuzu models, including Rodeo.

Cardone
1996 Isuzu Hombre Engine Control Module Cardone - Reman. A-1 CARDONE Powertrain Control Module

P311-5DC7369    77-5830F  Remanufactured

16231851 , 8162158300 , 16215830

Qty:
$89.05
Cardone Engine Control Module
  • Remanufactured Powertrain Control Module
  • Vehicle specific Flash programming req'd ON or OFF the vehicle.Accurate VIN and mileage are req'd. Additional vehicle specific on-car programming must be performed AFTER installation to prevent drivability and starting issues. Knock Module must be removed from original PCM and installed in replacement PCM
  • Reman. A-1 CARDONE Powertrain Control Module
  • Product Attributes:
    • Connector/Terminal Configuration: Pin/male; Pin/male; Pin/male
    • FAQs:
      • Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Injection Pulse On Fuel Pump, Intermittent Starting Problems.
      • Chrysler Models 1996 And Newer Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?
      • Do Gm Vehicles Have A Passive Anti-theft System?
      • Do I Have To Transfer Anything From My Original Ecm/pcm?
      • Do I Need A Scanner To Reset The Anti-theft System
      • Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn.
      • No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application.
      • Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays.
      • Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module.
      • The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • What Are The Most Common Symptoms Of A Bad Pcm?
      • What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?
      • What’s The Difference Between An Ecm And A Pcm?
      • Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System.
      • “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission.
    • Features and Benefits:
      • Meets O.e. Fit And Function.
      • Meets Or Exceeds O.e.m Performance
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated, Computerized Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
    • Product Condition: Remanufactured
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design flaws. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back on the road with our remanufactured electronic and powertrain control modules.
Brand: Cardone
Additional Fitment Information:
Vehicle
1996 - Isuzu Hombre
Cardone
2007 Isuzu i-370 Engine Control Module 5 Cyl 3.7L Cardone - Reman. A-1 CARDONE Engine Control Computer

P311-4701D4E    77-2010F  Remanufactured

12602010 , 8126020100

Qty:
$52.20 $244.83
Cardone Engine Control Module
  • Remanufactured Engine Control Computer
  • Vehicle specific Flash programming req'd ON or OFF the vehicle.Accurate VIN and mileage are req'd. Additional vehicle specific on-car programming must be performed AFTER installation to prevent drivability and starting issues.
  • Reman. A-1 CARDONE Engine Control Computer
  • Product Attributes:
    • Connector/Terminal Configuration: Pin/male; Pin/male; Pin/male
    • FAQs:
      • Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Injection Pulse On Fuel Pump, Intermittent Starting Problems.
      • Chrysler Models 1996 And Newer Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?
      • Do Gm Vehicles Have A Passive Anti-theft System?
      • Do I Have To Transfer Anything From My Original Ecm/pcm?
      • Do I Need A Scanner To Reset The Anti-theft System
      • Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn.
      • No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application.
      • Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays.
      • Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module.
      • The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • What Are The Most Common Symptoms Of A Bad Pcm?
      • What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?
      • What’s The Difference Between An Ecm And A Pcm?
      • Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System.
      • “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission.
    • Features and Benefits:
      • Meets O.e. Fit And Function.
      • Meets Or Exceeds O.e.m Performance
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated, Computerized Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
    • Product Condition: Remanufactured
    • Terminal Quantity: 56; 73; 44
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design flaws. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back on the road with our remanufactured electronic and powertrain control modules.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
2007 - Isuzu i-370 L 5 Cyl 3.7L 223 3654
Cardone
2003 Isuzu Ascender Engine Control Module 6 Cyl 4.2L Cardone - Reman. A-1 CARDONE Powertrain Control Module

P311-3C2149D    77-4976F  Remanufactured

12574976 , 8125749760

Qty:
$218.36
Cardone Engine Control Module
  • Remanufactured Powertrain Control Module
  • Vehicle specific Flash programming req'd ON or OFF the vehicle.Accurate VIN and mileage are req'd. Additional vehicle specific on-car programming must be performed AFTER installation to prevent drivability and starting issues.
  • Reman. A-1 CARDONE Powertrain Control Module
  • Product Attributes:
    • Connector/Terminal Configuration: Pin/male; Pin/male; Pin/male
    • FAQs:
      • Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Injection Pulse On Fuel Pump, Intermittent Starting Problems.
      • Chrysler Models 1996 And Newer Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?
      • Do Gm Vehicles Have A Passive Anti-theft System?
      • Do I Have To Transfer Anything From My Original Ecm/pcm?
      • Do I Need A Scanner To Reset The Anti-theft System
      • Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn.
      • No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application.
      • Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays.
      • Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module.
      • The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • What Are The Most Common Symptoms Of A Bad Pcm?
      • What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?
      • What’s The Difference Between An Ecm And A Pcm?
      • Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System.
      • “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission.
    • Features and Benefits:
      • Meets O.e. Fit And Function.
      • Meets Or Exceeds O.e.m Performance
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated, Computerized Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
    • Product Condition: Remanufactured
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design flaws. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back on the road with our remanufactured electronic and powertrain control modules.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
2003 - Isuzu Ascender L 6 Cyl 4.2L 256 -
Cardone
2004 Isuzu Ascender Engine Control Module 8 Cyl 5.3L Cardone - Reman. A-1 CARDONE Engine Control Computer

P311-4AF5777    77-6242F  Remanufactured

12586242 , 8125862420

Qty:
$35.10 $160.33
Cardone Engine Control Module
  • Remanufactured Engine Control Computer
  • Vehicle specific Flash programming req'd ON or OFF the vehicle.Accurate VIN and mileage are req'd. Additional vehicle specific on-car programming must be performed AFTER installation to prevent drivability and starting issues.
  • Reman. A-1 CARDONE Engine Control Computer
  • Product Attributes:
    • Connector/Terminal Configuration: Pin/male; Pin/male
    • FAQs:
      • Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Injection Pulse On Fuel Pump, Intermittent Starting Problems.
      • Chrysler Models 1996 And Newer Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?
      • Do Gm Vehicles Have A Passive Anti-theft System?
      • Do I Have To Transfer Anything From My Original Ecm/pcm?
      • Do I Need A Scanner To Reset The Anti-theft System
      • Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn.
      • No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application.
      • Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays.
      • Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module.
      • The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • What Are The Most Common Symptoms Of A Bad Pcm?
      • What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?
      • What’s The Difference Between An Ecm And A Pcm?
      • Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System.
      • “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission.
    • Features and Benefits:
      • Meets O.e. Fit And Function.
      • Meets Or Exceeds O.e.m Performance
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated, Computerized Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
    • Product Condition: Remanufactured
    • Terminal Quantity: 80, 80
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design flaws. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back on the road with our remanufactured electronic and powertrain control modules.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
2004 - Isuzu Ascender V 8 Cyl 5.3L 325 5328
Cardone
2006 Isuzu i-350 Engine Control Module 5 Cyl 3.5L Cardone - Reman. A-1 CARDONE Powertrain Control Module

P311-4CFA324    77-7521F  Remanufactured

8125975210 , 12597521

Qty:
$41.40 $188.37
Cardone Engine Control Module
  • Remanufactured Powertrain Control Module
  • Vehicle specific Flash programming req'd ON or OFF the vehicle.Accurate VIN and mileage are req'd. Additional vehicle specific on-car programming must be performed AFTER installation to prevent drivability and starting issues.
  • Reman. A-1 CARDONE Powertrain Control Module
  • Product Attributes:
    • Connector/Terminal Configuration: Pin/male; Pin/male; Pin/male
    • FAQs:
      • Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Injection Pulse On Fuel Pump, Intermittent Starting Problems.
      • Chrysler Models 1996 And Newer Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?
      • Do Gm Vehicles Have A Passive Anti-theft System?
      • Do I Have To Transfer Anything From My Original Ecm/pcm?
      • Do I Need A Scanner To Reset The Anti-theft System
      • Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn.
      • No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application.
      • Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays.
      • Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module.
      • The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • What Are The Most Common Symptoms Of A Bad Pcm?
      • What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?
      • What’s The Difference Between An Ecm And A Pcm?
      • Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System.
      • “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission.
    • Features and Benefits:
      • Meets O.e. Fit And Function.
      • Meets Or Exceeds O.e.m Performance
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated, Computerized Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
    • Product Condition: Remanufactured
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design flaws. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back on the road with our remanufactured electronic and powertrain control modules.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
2006 - Isuzu i-350 L 5 Cyl 3.5L 211 3460
Cardone
1997 Isuzu Hombre Engine Control Module 4 Cyl 2.2L Cardone - Reman. A-1 CARDONE Powertrain Control Module

P311-437AA54    77-8016F  Remanufactured

16228016 , 8162280160

Qty:
$103.06
Cardone Engine Control Module
  • Remanufactured Powertrain Control Module
  • Vehicle specific Flash programming req'd ON or OFF the vehicle.Accurate VIN and mileage are req'd. Additional vehicle specific on-car programming must be performed AFTER installation to prevent drivability and starting issues.
  • Reman. A-1 CARDONE Powertrain Control Module
  • Product Attributes:
    • Connector/Terminal Configuration: Pin/male; Pin/male; Pin/male; Pin/male
    • FAQs:
      • Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Injection Pulse On Fuel Pump, Intermittent Starting Problems.
      • Chrysler Models 1996 And Newer Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?
      • Do Gm Vehicles Have A Passive Anti-theft System?
      • Do I Have To Transfer Anything From My Original Ecm/pcm?
      • Do I Need A Scanner To Reset The Anti-theft System
      • Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn.
      • No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application.
      • Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays.
      • Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module.
      • The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • What Are The Most Common Symptoms Of A Bad Pcm?
      • What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?
      • What’s The Difference Between An Ecm And A Pcm?
      • Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System.
      • “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission.
    • Features and Benefits:
      • Meets O.e. Fit And Function.
      • Meets Or Exceeds O.e.m Performance
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated, Computerized Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
    • Product Condition: Remanufactured
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design flaws. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back on the road with our remanufactured electronic and powertrain control modules.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
1997 - Isuzu Hombre L 4 Cyl 2.2L 134 2190
Cardone
2003 Isuzu Ascender Engine Control Module 8 Cyl 5.3L Cardone - Reman. A-1 CARDONE Engine Control Computer

P311-12DD16F    77-2605F  Remanufactured

8125826050 , 12582605

Qty:
$48.60 $150.68
Cardone Engine Control Module
  • Remanufactured Engine Control Computer
  • Vehicle specific Flash programming req'd ON or OFF the vehicle.Accurate VIN and mileage are req'd. Additional vehicle specific on-car programming must be performed AFTER installation to prevent drivability and starting issues.
  • Reman. A-1 CARDONE Engine Control Computer
  • Product Attributes:
    • Connector/Terminal Configuration: Pin/male; Pin/male
    • FAQs:
      • Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Injection Pulse On Fuel Pump, Intermittent Starting Problems.
      • Chrysler Models 1996 And Newer Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?
      • Do Gm Vehicles Have A Passive Anti-theft System?
      • Do I Have To Transfer Anything From My Original Ecm/pcm?
      • Do I Need A Scanner To Reset The Anti-theft System
      • Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn.
      • No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application.
      • Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays.
      • Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module.
      • The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • What Are The Most Common Symptoms Of A Bad Pcm?
      • What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?
      • What’s The Difference Between An Ecm And A Pcm?
      • Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System.
      • “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission.
    • Features and Benefits:
      • Meets O.e. Fit And Function.
      • Meets Or Exceeds O.e.m Performance
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated, Computerized Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
    • Product Condition: Remanufactured
    • Terminal Quantity: 80, 80
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design flaws. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back on the road with our remanufactured electronic and powertrain control modules.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
2003 - Isuzu Ascender V 8 Cyl 5.3L 325 5328
Cardone
1998 Isuzu Hombre Engine Control Module 6 Cyl 4.3L Cardone - Reman. A-1 CARDONE Engine Control Computer

P311-53EA1C7    77-0279F  Remanufactured

9366810 , 8162502790 , 16250279 , 9355699 , 8093556990

Qty:
$48.60 $103.06
Cardone Engine Control Module
  • Remanufactured Engine Control Computer
  • Vehicle specific Flash programming req'd ON or OFF the vehicle.Accurate VIN and mileage are req'd. Additional vehicle specific on-car programming must be performed AFTER installation to prevent drivability and starting issues. Knock Module must be removed from original PCM and installed in replacement PCM
  • Reman. A-1 CARDONE Engine Control Computer
  • Product Attributes:
    • Connector/Terminal Configuration: Pin/male; Pin/male; Pin/male; Pin/male
    • FAQs:
      • Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Injection Pulse On Fuel Pump, Intermittent Starting Problems.
      • Chrysler Models 1996 And Newer Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?
      • Do Gm Vehicles Have A Passive Anti-theft System?
      • Do I Have To Transfer Anything From My Original Ecm/pcm?
      • Do I Need A Scanner To Reset The Anti-theft System
      • Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn.
      • No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application.
      • Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays.
      • Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module.
      • The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • What Are The Most Common Symptoms Of A Bad Pcm?
      • What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?
      • What’s The Difference Between An Ecm And A Pcm?
      • Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System.
      • “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission.
    • Features and Benefits:
      • Meets O.e. Fit And Function.
      • Meets Or Exceeds O.e.m Performance
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated, Computerized Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
    • Product Condition: Remanufactured
    • Terminal Quantity: 32, 32, 32, 24
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design flaws. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back on the road with our remanufactured electronic and powertrain control modules.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
1998 - Isuzu Hombre V 6 Cyl 4.3L - 4294
Cardone
2006 Isuzu i-350 Engine Control Module Cardone - Reman. A-1 CARDONE Engine Control Computer

P311-25C9E93    77-9773F  Remanufactured

12569773 , 8125697730

Qty:
$41.40 $176.58
Cardone Engine Control Module
  • Remanufactured Engine Control Computer
  • Vehicle specific Flash programming req'd ON or OFF the vehicle.Accurate VIN and mileage are req'd. Additional vehicle specific on-car programming must be performed AFTER installation to prevent drivability and starting issues.
  • Reman. A-1 CARDONE Engine Control Computer
  • Product Attributes:
    • Connector/Terminal Configuration: Pin/male; Pin/male; Pin/male
    • FAQs:
      • Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Injection Pulse On Fuel Pump, Intermittent Starting Problems.
      • Chrysler Models 1996 And Newer Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?
      • Do Gm Vehicles Have A Passive Anti-theft System?
      • Do I Have To Transfer Anything From My Original Ecm/pcm?
      • Do I Need A Scanner To Reset The Anti-theft System
      • Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn.
      • No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application.
      • Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays.
      • Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module.
      • The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • What Are The Most Common Symptoms Of A Bad Pcm?
      • What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?
      • What’s The Difference Between An Ecm And A Pcm?
      • Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System.
      • “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission.
    • Features and Benefits:
      • Meets O.e. Fit And Function.
      • Meets Or Exceeds O.e.m Performance
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated, Computerized Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
    • Product Condition: Remanufactured
    • Terminal Quantity: 56, 73, 44
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design flaws. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back on the road with our remanufactured electronic and powertrain control modules.
Brand: Cardone
Additional Fitment Information:
Vehicle
2006 - Isuzu i-350
Cardone
1988 Isuzu I-Mark Engine Control Module Cardone - Reman. A-1 CARDONE Engine Control Computer

P311-23DA008    77-8546  Remanufactured

8160743790 , 1228546

Qty:
$87.94
Cardone Engine Control Module
  • Remanufactured Engine Control Computer
  • The PROM(s)/CALPACK must be transferred from the original module to the replacement module.
  • Reman. A-1 CARDONE Engine Control Computer
  • Product Attributes:
    • Connector/Terminal Configuration: Edge/male
    • FAQs:
      • Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Injection Pulse On Fuel Pump, Intermittent Starting Problems.
      • Chrysler Models 1996 And Newer Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?
      • Do Gm Vehicles Have A Passive Anti-theft System?
      • Do I Have To Transfer Anything From My Original Ecm/pcm?
      • Do I Need A Scanner To Reset The Anti-theft System
      • Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn.
      • No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application.
      • Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays.
      • Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module.
      • The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • What Are The Most Common Symptoms Of A Bad Pcm?
      • What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?
      • What’s The Difference Between An Ecm And A Pcm?
      • Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System.
      • “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission.
    • Features and Benefits:
      • Meets O.e. Fit And Function.
      • Meets Or Exceeds O.e.m Performance
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated, Computerized Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
    • Product Condition: Remanufactured
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design flaws. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back on the road with our remanufactured electronic and powertrain control modules.
Brand: Cardone
Additional Fitment Information:
Vehicle Transmission Aspiration
1988 - Isuzu I-Mark Automatic Naturally Aspirated
Cardone
1991 Isuzu Stylus Engine Control Module Cardone - Reman. A-1 CARDONE Engine Control Computer

P311-15B818C    77-1237AC  Remanufactured

16161229 , 8161612370 , 16161237

Qty:
$39.60 $248.35
Cardone Engine Control Module
  • Remanufactured Engine Control Computer
  • Units are pre-programmed at the factory.
  • Reman. A-1 CARDONE Engine Control Computer
  • Product Attributes:
    • Connector/Terminal Configuration: Pin/male; Pin/male
    • FAQs:
      • Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Injection Pulse On Fuel Pump, Intermittent Starting Problems.
      • Chrysler Models 1996 And Newer Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?
      • Do Gm Vehicles Have A Passive Anti-theft System?
      • Do I Have To Transfer Anything From My Original Ecm/pcm?
      • Do I Need A Scanner To Reset The Anti-theft System
      • Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn.
      • No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application.
      • Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays.
      • Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module.
      • The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • What Are The Most Common Symptoms Of A Bad Pcm?
      • What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?
      • What’s The Difference Between An Ecm And A Pcm?
      • Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System.
      • “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission.
    • Features and Benefits:
      • Meets O.e. Fit And Function.
      • Meets Or Exceeds O.e.m Performance
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated, Computerized Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
    • Product Condition: Remanufactured
    • Terminal Quantity: 32, 24
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design flaws. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back on the road with our remanufactured electronic and powertrain control modules.
Brand: Cardone
Additional Fitment Information:
Vehicle Transmission
1991 - Isuzu Stylus Automatic
Cardone
1992 Isuzu Stylus Engine Control Module 4 Cyl 1.6L Cardone - Reman. A-1 CARDONE Engine Control Computer

P311-56EFBC6    77-1237MF  Remanufactured

16161237 , 16161229

Qty:
$35.10 $89.05
Cardone Engine Control Module
  • Remanufactured Engine Control Computer
  • Units are pre-programmed at the factory.
  • Reman. A-1 CARDONE Engine Control Computer
  • Product Attributes:
    • Connector/Terminal Configuration: Pin/male; Pin/male
    • FAQs:
      • Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Injection Pulse On Fuel Pump, Intermittent Starting Problems.
      • Chrysler Models 1996 And Newer Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?
      • Do Gm Vehicles Have A Passive Anti-theft System?
      • Do I Have To Transfer Anything From My Original Ecm/pcm?
      • Do I Need A Scanner To Reset The Anti-theft System
      • Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn.
      • No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application.
      • Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays.
      • Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module.
      • The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • What Are The Most Common Symptoms Of A Bad Pcm?
      • What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?
      • What’s The Difference Between An Ecm And A Pcm?
      • Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System.
      • “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission.
    • Features and Benefits:
      • Meets O.e. Fit And Function.
      • Meets Or Exceeds O.e.m Performance
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated, Computerized Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
    • Product Condition: Remanufactured
    • Terminal Quantity: 32, 24
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design flaws. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back on the road with our remanufactured electronic and powertrain control modules.
Brand: Cardone
Additional Fitment Information:
Vehicle Transmission Block Engine CID CC
1992 - Isuzu Stylus Manual L 4 Cyl 1.6L - 1588
Cardone
1993 Isuzu Stylus Engine Control Module Cardone - Reman. A-1 CARDONE Engine Control Computer

P311-0A3CF2D    77-1219MF  Remanufactured

16176819 , 8161768190 , 16181219

Qty:
$24.30 $87.94
Cardone Engine Control Module
  • Remanufactured Engine Control Computer
  • Units are pre-programmed at the factory.
  • Reman. A-1 CARDONE Engine Control Computer
  • Product Attributes:
    • Connector/Terminal Configuration: Pin/male; Pin/male
    • FAQs:
      • Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Injection Pulse On Fuel Pump, Intermittent Starting Problems.
      • Chrysler Models 1996 And Newer Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?
      • Do Gm Vehicles Have A Passive Anti-theft System?
      • Do I Have To Transfer Anything From My Original Ecm/pcm?
      • Do I Need A Scanner To Reset The Anti-theft System
      • Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn.
      • No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application.
      • Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays.
      • Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module.
      • The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • What Are The Most Common Symptoms Of A Bad Pcm?
      • What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?
      • What’s The Difference Between An Ecm And A Pcm?
      • Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System.
      • “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission.
    • Features and Benefits:
      • Meets O.e. Fit And Function.
      • Meets Or Exceeds O.e.m Performance
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated, Computerized Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
    • Product Condition: Remanufactured
    • Terminal Quantity: 32, 24
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design flaws. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back on the road with our remanufactured electronic and powertrain control modules.
Brand: Cardone
Additional Fitment Information:
Vehicle Transmission
1993 - Isuzu Stylus Manual
Cardone
1992 Isuzu Stylus Engine Control Module 4 Cyl 1.6L Cardone - Reman. A-1 CARDONE Engine Control Computer

P311-0C1A42D    77-1237AF  Remanufactured

8161612370 , 8161612290 , 16161229 , 16161237

Qty:
$80.10 $87.94
Cardone Engine Control Module
  • Remanufactured Engine Control Computer
  • Units are pre-programmed at the factory.
  • Reman. A-1 CARDONE Engine Control Computer
  • Product Attributes:
    • Connector/Terminal Configuration: Pin/male; Pin/male
    • FAQs:
      • Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Injection Pulse On Fuel Pump, Intermittent Starting Problems.
      • Chrysler Models 1996 And Newer Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?
      • Do Gm Vehicles Have A Passive Anti-theft System?
      • Do I Have To Transfer Anything From My Original Ecm/pcm?
      • Do I Need A Scanner To Reset The Anti-theft System
      • Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn.
      • No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application.
      • Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays.
      • Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module.
      • The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • What Are The Most Common Symptoms Of A Bad Pcm?
      • What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?
      • What’s The Difference Between An Ecm And A Pcm?
      • Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System.
      • “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission.
    • Features and Benefits:
      • Meets O.e. Fit And Function.
      • Meets Or Exceeds O.e.m Performance
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated, Computerized Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
    • Product Condition: Remanufactured
    • Terminal Quantity: 32, 24
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design flaws. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back on the road with our remanufactured electronic and powertrain control modules.
Brand: Cardone
Additional Fitment Information:
Vehicle Transmission Block Engine CID CC
1992 - Isuzu Stylus Automatic L 4 Cyl 1.6L - 1588
Cardone
1993 Isuzu Stylus Engine Control Module Cardone - Reman. A-1 CARDONE Engine Control Computer

P311-4241E84    77-1219AC  Remanufactured

16176789 , 16181219 , 8161767890

Qty:
$24.30 $108.41
Cardone Engine Control Module
  • Remanufactured Engine Control Computer
  • Units are pre-programmed at the factory.
  • Reman. A-1 CARDONE Engine Control Computer
  • Product Attributes:
    • Connector/Terminal Configuration: Pin/male; Pin/male
    • FAQs:
      • Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Injection Pulse On Fuel Pump, Intermittent Starting Problems.
      • Chrysler Models 1996 And Newer Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?
      • Do Gm Vehicles Have A Passive Anti-theft System?
      • Do I Have To Transfer Anything From My Original Ecm/pcm?
      • Do I Need A Scanner To Reset The Anti-theft System
      • Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn.
      • No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application.
      • Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays.
      • Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module.
      • The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • What Are The Most Common Symptoms Of A Bad Pcm?
      • What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?
      • What’s The Difference Between An Ecm And A Pcm?
      • Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System.
      • “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission.
    • Features and Benefits:
      • Meets O.e. Fit And Function.
      • Meets Or Exceeds O.e.m Performance
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated, Computerized Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
    • Product Condition: Remanufactured
    • Terminal Quantity: 32, 24
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design flaws. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back on the road with our remanufactured electronic and powertrain control modules.
Brand: Cardone
Additional Fitment Information:
Vehicle Transmission
1993 - Isuzu Stylus Automatic
Cardone
1993 Isuzu Stylus Engine Control Module Cardone - Reman. A-1 CARDONE Engine Control Computer

P311-4D6F8F7    77-1219MC  Remanufactured

8161767990 , 16176799 , 16181219

Qty:
$24.30 $87.94
Cardone Engine Control Module
  • Remanufactured Engine Control Computer
  • Units are pre-programmed at the factory.
  • Reman. A-1 CARDONE Engine Control Computer
  • Product Attributes:
    • Connector/Terminal Configuration: Pin/male; Pin/male
    • FAQs:
      • Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Injection Pulse On Fuel Pump, Intermittent Starting Problems.
      • Chrysler Models 1996 And Newer Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?
      • Do Gm Vehicles Have A Passive Anti-theft System?
      • Do I Have To Transfer Anything From My Original Ecm/pcm?
      • Do I Need A Scanner To Reset The Anti-theft System
      • Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn.
      • No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application.
      • Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays.
      • Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module.
      • The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • What Are The Most Common Symptoms Of A Bad Pcm?
      • What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?
      • What’s The Difference Between An Ecm And A Pcm?
      • Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System.
      • “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission.
    • Features and Benefits:
      • Meets O.e. Fit And Function.
      • Meets Or Exceeds O.e.m Performance
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated, Computerized Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
    • Product Condition: Remanufactured
    • Terminal Quantity: 32, 24
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design flaws. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back on the road with our remanufactured electronic and powertrain control modules.
Brand: Cardone
Additional Fitment Information:
Vehicle Transmission
1993 - Isuzu Stylus Manual
Cardone
1993 Isuzu Stylus Engine Control Module Cardone - Reman. A-1 CARDONE Engine Control Computer

P311-0554303    77-1219AF  Remanufactured

8161768090 , 8161767890 , 16181219 , 8161767990 , 8161768190 , 16176809 , 16176789 , 16176819 , 16176799

Qty:
$35.10 $87.94
Cardone Engine Control Module
  • Remanufactured Engine Control Computer
  • Units are pre-programmed at the factory.
  • Reman. A-1 CARDONE Engine Control Computer
  • Product Attributes:
    • Connector/Terminal Configuration: Pin/male; Pin/male
    • FAQs:
      • Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Injection Pulse On Fuel Pump, Intermittent Starting Problems.
      • Chrysler Models 1996 And Newer Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?
      • Do Gm Vehicles Have A Passive Anti-theft System?
      • Do I Have To Transfer Anything From My Original Ecm/pcm?
      • Do I Need A Scanner To Reset The Anti-theft System
      • Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn.
      • No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application.
      • Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays.
      • Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module.
      • The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • What Are The Most Common Symptoms Of A Bad Pcm?
      • What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?
      • What’s The Difference Between An Ecm And A Pcm?
      • Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System.
      • “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission.
    • Features and Benefits:
      • Meets O.e. Fit And Function.
      • Meets Or Exceeds O.e.m Performance
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated, Computerized Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
    • Product Condition: Remanufactured
    • Terminal Quantity: 32, 24
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design flaws. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back on the road with our remanufactured electronic and powertrain control modules.
Brand: Cardone
Additional Fitment Information:
Vehicle Transmission
1993 - Isuzu Stylus Automatic
Cardone
1994 Isuzu Rodeo Engine Control Module 6 Cyl 3.2L Cardone - Reman. A-1 CARDONE Engine Control Computer

P311-11A2BB7    72-4087  Remanufactured

8162011490

Qty:
$52.20 $288.05
Cardone Engine Control Module
  • Remanufactured Engine Control Computer
  • Units are pre-programmed at the factory.
  • Reman. A-1 CARDONE Engine Control Computer
  • Product Attributes:
    • Connector/Terminal Configuration: Pin/male; Pin/male
    • FAQs:
      • Check Engine Light Staying On After Resetting, Engine Turning Off For No Reason, Loss Of Spark, Loss Of Injection Pulse On Fuel Pump, Intermittent Starting Problems.
      • Chrysler Models 1996 And Newer Will Need To Be Vin Programmed.
      • Do All Chrysler Power Train Control Modules (pcm) Need Vin Programming?
      • Do All Ford Vehicles Require A Passive Anti-theft System (p.a.t.s) Reset?
      • Do Gm Vehicles Have A Passive Anti-theft System?
      • Do I Have To Transfer Anything From My Original Ecm/pcm?
      • Do I Need A Scanner To Reset The Anti-theft System
      • Ensure That The Pcm Was Properly Flash Programmed For The Vehicle. Also Note Whether The Vehicle Is Equipped With The Ford "passive Anti-theft System", Which Requires An On-car Relearn.
      • No, Not All Ford Vehicles Require Pats Reset. Check The Pats Chart Found On The O.e. Manufacturer’s Service Site For Your Application.
      • Not Necessarily. There Is A 30-minute Manual Procedure That Can Be Done Without A Scanner. Refer To Your O.e. Manufacturer’s Approved Service Manual For Details.
      • Prior To Replacing The Original Ecm/pcm, The Installer Should Determine What Caused The Original To Fail. Common Causes Of Failures Are: Poor Grounds And Power, A Bad Wiring Harness And Short-circuited Solenoids/relays.
      • Some Gm Applications Have A Knock Module That Must Be Transferred To The Replacement Module. Some Older Ford Applications Have A Calibration Module That Must Be Transferred To The Replacement Module.
      • The Replacement Pcm For A Ford Vehicle Won’t Start The Vehicle. Why?
      • What Are The Most Common Symptoms Of A Bad Pcm?
      • What Steps Should I Take To Ensure The Original Pcm Is Causing The Issue?
      • What’s The Difference Between An Ecm And A Pcm?
      • Yes, Most Gm Vehicles Have A Vats, Pass Key Or Pass Lock Anti-theft System.
      • “ecm” Stands For Electronic Control Module. “pcm” Stands For Powertrain Control Module. Both The Ecm And Pcm Control The Engine; However, The Pcm Also Has Control Over The Transmission.
    • Features and Benefits:
      • Meets O.e. Fit And Function.
      • Meets Or Exceeds O.e.m Performance
      • On-car Vehicle Validation Is Done To Test Durability And Performance.
      • Re-soldering Of Critical Components Ensures Superior Electrical Connections. This Prevents Intermittent Failures And Leads To Longer Product Life.
      • Tested With Automated, Computerized Equipment Or Bench-tested, Depending On Application, To Ensure Functionality.
    • Product Condition: Remanufactured
    • Terminal Quantity: 32, 24
  • CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design flaws. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back on the road with our remanufactured electronic and powertrain control modules.
Brand: Cardone
Additional Fitment Information:
Vehicle Block Engine CID CC
1994 - Isuzu Rodeo V 6 Cyl 3.2L - 3165